AG Neovo Universal Remote TSC 40 IC User Manual

Analog Resistive Touch Screen Controller  
TSC-40/IC product specification  
 
TSC-40/IC Product Specification  
1. PRODUCTS OUTLINE  
1-1. Scope of Application  
This specification applies to the TSC-40/IC.  
1-2. Outline  
TSC-40/IC is an analog touch screen control IC that performs A/D conversion on analog signal for the  
4-wire and 5-wire resistive analog touch screen, and transmits coordination data with 10bit resolution to  
the host in a 9600bps serial (asynchronous).  
The serial communication enables a connection with PC’s serial port via RS-232C I/F circuit or TTL level.  
At the coordinate detection, internal filtering process provides a stabilized coordinate value. By using the  
correction function, in addition to the losses that occur in the circuit, display deflection between touch  
screen input point that occur in each element and indicator cursor can be corrected to adjust the display  
position.  
1-3. Features  
§
Two coordinate output modes are provided and selected per application: “Coordinate data mode”  
where coordinate information is sent with 10bit resolution as it is, and “correction data mode” where  
read coordinate is converted to the indicator’s display coordinate and sent.  
§
“Correction data mode“ is available after EEPROM is externally attached. It enables to set up to nine  
correction points. Coordinate data can be corrected with the base of correction points. Using this  
function allows the host driver to make the implementation of correction function unnecessary. In  
addition, by placing correction points at the touch screen center and center points of four edges of  
touch screen, resistance value deviation of transparent electrode film can be corrected.  
§
Two external switch functions are always available in the coordinate (correction) data mode. Two  
pieces of external switch information are, at the transmission of coordinate data, included in the  
coordinate data as pen-down/pen-up information. Since in the pen-up mode, pen-up data can be  
always output to the host, this switch is available as a function switch.  
§
§
§
At the touch screen input, buzzer and LED outputs are available. Input confirmation via display and  
sound is available.  
When no touch screen input is performed, the state moves to “power-save mode“ so that such  
application can be supported that requests a low power consumption.  
Seven types of coordinate output rates are provided and either can be selected per application among  
seven types: six types from 30 to 150p/s plus one type, a point mode that outputs the coordinate only  
one time when pen-down is performed.  
Document No. DER-S0026A  
2
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
1-4. General specification  
Item  
Rating  
DC 3.3V to 5.5V  
Notes  
Power supply voltage  
Power consumption  
29.5mW (standard)  
-20 ˚C to +85 ˚C  
(No dew condensation)  
Operating Temp  
-40 ˚C to +125 ˚C  
(No dew condensation)  
Temperature range at storing  
Communication scheme  
Asynchronous, serial  
Communication rate  
Data length  
Stop bit  
9600bps  
8bits  
Communication  
scheme  
Each setting is fixed  
Fixed to 6MHz  
1bit  
Parity  
None  
Operation frequency  
6MHz  
(1) Point mode  
Point Mode: Only when touch screen is  
input, pen-down ID is sent once. After  
input ends, no pen-up ID is sent.  
(2) 30p/s  
(4) 80p/s  
(6) 130p/s  
(3) 50p/s  
(5) 100p/s  
(7) 150p/s  
Coordinate output rate (point / second)  
Linearity error  
±3 LSB  
Input response time  
10ms (TYP)  
150p/s, For coordinate data mode.  
In the correction data function,  
resolution follows the setting value  
Coordinate resolution  
Dimension (mm)  
10bit (1024×1024)  
9×9×1.7  
Document No. DER-S0026A  
3
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
2. Pin layout and representation  
SEL0  
RxD  
25  
26  
27  
28  
29  
30  
31  
32  
16  
15  
14  
13  
12  
11  
10  
9
SEL4/EEP-CS  
SEL3/EEP-CLK  
SEL2/EEP-DI  
LED1  
TSC-40x  
TxD  
SW1  
SW0  
BEEP  
AN0  
xxx  
P30  
VSS  
INDEX  
XOUT  
####  
AN1  
XIN  
Marking specification  
TSC-40x  
xxx  
Product number x: version number  
ROM number  
####  
Lot number  
Document No. DER-S0026A  
4
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
3. Pin functions  
Pin  
number  
Pin name  
I/O  
Functional description  
1
2
AN2  
AN3  
I/O Touch screen XL/UR input pin.  
I/O Touch screen XR/LL input pin.  
Transition select pin.  
I
3
SEL1  
H = Auto transition*1 after reset. L = transition by command.  
EEPROM DO input pin; At using no EEPROM, Vcc or GND is connected.  
A/D converter reference voltage input pin; Vcc is connected.  
Reset input pin (active L).  
4
5
EEP-DO  
VREF  
I
I
RST  
6
I
7
CNVSS  
VCC  
I
Operation mode control pin; Vss is connected.  
Power supply input pin; Vcc is connected.  
8
I
9
XIN  
I
Clock input pin; When using external clock, clock is input to this pin.  
Clock output pin; When using external clock, this pin is opened.  
Power supply input pin (GND); GND is connected.  
Opened*2.  
10  
11  
12  
13  
XOUT  
VSS  
O
I
P30  
O
O
LED1  
LED output pin; ON = Lo, OFF = Hi.  
EEPROM DI signal output pin; When using EEPROM, EEPROM DI is connected.  
Whether or not EEPROM is used, connect with GND via resistance.  
14*3  
SEL2/EEP-DI  
I/O  
EEPROM SK signal output pin; When using EEPROM, EEPROM SK is connected.  
15*3  
SEL3/EEP-CLK I/O Touch screen mode setting pin. (L=4-wire, H=5-wire)  
Whether or not EEPROM is used, connect with Vcc or GND via resistance.  
EEPROM setting pin shared with EEPROM CS signal output pin.  
EEPROM is set via resistance and Vcc or GND is connected. (L = Used, H = Not  
used).  
16*3  
SEL4/EEP-CS  
I/O  
When using EEPROM, EEPROM CS is connected.  
17  
18  
19  
20  
21  
22  
23  
O
O
O
O
O
O
I
Unused pin; Opened.  
SYD/LL  
SYU/UL  
SXL/UR  
SXR/LR  
THO  
Touch screen LL control pin.  
Touch screen UL control pin.  
Touch screen UR control pin.  
Touch screen LR control pin.  
Pen down detection pin.  
THI  
In power-save mode, start signal input pin by pen down.  
In power-save mode, start signal input pin by command reception.  
Only used serial mode, RxD is connected.  
24  
25  
RxD_I  
SEL0  
I
I
If power supply voltage is 4.0 to 5.5V, GND is connected. If power supply voltage is  
3.3 to 4.0V, Vcc is connected.  
26  
27  
28  
29  
30  
31  
32  
RxD  
TxD  
I/O Data receive pin.  
I/O Data send pin.  
SW1  
SW0  
BEEP  
AN0  
I
I
SW1 input pin *4; H = ON = 1, L = OFF = 0.  
SW0 input pin *4; H = ON = 1, L = OFF = 0.  
BEEP output pin; Hi output; Output frequency =2.5kHz, Output time =50ms.  
Touch screen YD/LL input pin.  
O
I
AN1  
I
Touch screen YU/Sense input pin.  
Document No. DER-S0026A  
5
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
*1: Auto transition = Mode changes by a command are not performed. It becomes a “Coordinate Data  
Mode (150pps)” immediately after reset.  
*2: Always open. If connected with VCC, VSS, or other circuit, an error operation may occur.  
*3: About pin number 14, 15 and 16, immediately after a power supply injection, it works as an input  
terminal and becomes an output terminal after that. Do not open these terminals.  
*4: If neither SW0 nor SW1 function is used, connect 28 and 29 pins to GND directly.  
Document No. DER-S0026A  
6
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
4. Initial setting  
4-1. EEPROM setting  
Depending on that calibration is performed in either TSC-40/IC or host, you can select whether EEPROM  
is used or not to store the correction data. EEPROM selection can be set via pin number 16, where  
hardware reset release enables the setting.  
VCC  
(TSC-40/IC)  
(EEPROM)  
H= Not used  
SEL4/EEP-CS  
L= Used  
CS  
4-2. Touch screen mode setting  
Touch screen mode setting for 4-wire/5-wire is performed by setting pin number 15 to “H” or “L”. When  
power supply is turned on, or hardware reset is released, pin number 15 is read to turn on in either  
4-wire/5-wire mode.  
Mode  
Pin number 15  
GND  
4-wire touch screen  
5-wire touch screen  
Vcc  
4-3. Power supply voltage setting  
Power supply mode setting for 3.3V/5V is performed by setting pin number 25 to “H” or “L”. When power  
supply is turned on, or hardware reset is released, pin number 25 is read to turn on in either 3.3V mode/5V  
mode.  
Power supply voltage  
3.3 to 4.0V  
Mode  
Pin number 25  
Vcc  
3.3V mode  
5V mode  
4.0 to 5.5V  
GND  
*When you operate it with 3.3V mode, the inside frequency of CPU works at 3MHz, and the sampling rate  
is 80pps max in calibration data mode.  
Document No. DER-S0026A  
7
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
5. Data sheet  
5-1. Absolute maximum rating  
Rating  
Maximum  
Item  
Symbol  
Unit  
Description  
Minimum  
Power supply voltage  
Input voltage  
VCC  
VI  
-0.3  
-0.3  
-0.3  
6.5  
Vcc+0.3  
Vcc+0.3  
200  
V
V
Output voltage  
VO  
V
Power consumption  
Operation temperature  
Storage temperature  
PD  
mW  
˚C  
˚C  
TOPR  
TSTG  
-20  
-40  
+85  
+125  
Document No. DER-S0026A  
8
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
5-2. Recommended operational conditions  
(Vcc=3.3 to 5.5V, Vss=0V, Ta=-20 to 85˚C, unless otherwise noted)  
Limits  
Item  
Symbol  
Unit  
Description  
Minimum  
3.3  
Standard  
Maximum  
5.5  
VCC  
VSS  
5.0  
0
V
V
V
Power supply voltage  
Power supply voltage  
Analog reference voltage  
VREF  
1.8  
VCC  
VCC  
“H” input voltage  
(Pin number 1 - 4, 12 - 32)  
“H” input voltage  
VIH  
VIH  
0.8VCC  
V
0.8VCC  
VCC  
0.2VCC  
0.2VCC  
0.16VCC  
-80  
V
RST, XIN  
“L” input voltage  
VIL  
0
0
0
V
(Pin number 1 - 4, 12 - 32)  
“L” input voltage  
VIL  
V
RST, CNVSS  
“L” input voltage  
VIL  
V
XIN  
“H” total peak output current *2  
(Pin number 1 - 4, 12 - 32)  
“L” total peak output current *2  
(Pin number 1 -4, 26 - 32)  
“L” total peak output current *2  
(Pin number 12 - 25)  
ΣIOH (peak)  
ΣIOL (peak)  
ΣIOL (peak)  
ΣIOH (avg)  
ΣIOL (avg)  
ΣIOL (avg)  
IOH (peak)  
IOL (peak)  
IOH (avg)  
mA  
mA  
mA  
mA  
mA  
mA  
mA  
mA  
mA  
80  
80  
“H” total average output current*2  
(Pin number 1 - 4, 12 - 32)  
“L” total average output current*2  
(Pin number 1 - 4, 26 - 32)  
“L” total average output current*2  
(pin number 12 - 25)  
-40  
40  
40  
“H” peak output current *3  
(Pin number 1 - 4, 12 - 32)  
“L” peak output current *3  
(Pin number 1 - 4, 12 - 32)  
“H” average output current *4  
(Pin number 1 - 4, 12 - 32)  
“L” average output current *4  
(Pin number 1 - 4, 12 - 32)  
-10  
10  
-5  
IOL (avg)  
XIN  
5
mA  
6.0  
MHz  
Vibration frequency  
*1 Vcc = 4.0 to 5.5V  
*2 The total output current is the sum of all the currents flowing through all the applicable ports. The total  
average current is an average value measured over 100ms. The total peak current is the peak value of  
all the currents.  
*3 The peak output current is the peak current flowing in each port.  
*4 The average output current IOL(avg), IOH(avg) in an average value measured over 100ms.  
*5 When the oscillation frequency has a duty cycle of 50%.  
Document No. DER-S0026A  
9
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
5-3. Timing requirement  
§
Reset  
(Vcc = 3.3 to 5.5V , Vss = 0V , Ta = -20 to 85°C)  
Limits  
Minimum Maximum  
Item  
RST L width  
Symbol  
tw  
Unit  
Description  
2
μs  
tw  
RST  
0.8Vcc  
0.8Vcc  
0.2Vcc  
0.2Vcc  
§
External clock timing  
Item  
Limits  
Symbol  
Unit  
Description  
Minimum  
Maximum  
Input cycle  
tC  
166  
70  
ns  
ns  
Clock frequency: Fixed to 6MHz  
Clock pulse width  
tWH, tWL  
tC  
tWH  
tWL  
0.8VCC  
0.2VCC  
XIN  
§
Clock input circuit  
Using ceramic vibrator  
CIN  
External clock input circuit  
XIN  
XIN  
XOUT  
Open  
XOUT  
COUT  
Document No. DER-S0026A  
10  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
5-4. DC standards  
(Vcc=3.3 to 5.5V, Vss=0V, Ta=-20 to 85˚C, unless otherwise noted)  
Limits  
Unit  
Item  
Symbol  
Condition  
Minimum  
Standard  
Maximum  
IOH = -5mA  
Vcc = 4.0 to 5.5V  
IOH = -1.0mA  
Vcc = 3.3 to 5.5V  
IOL = 5mA  
Vcc-1.5  
Output “H” voltage *1  
VOH  
V
V
(Pin number 1-4, 12-32)  
Vcc-1.0  
1.5  
0.3  
VCC = 4.0 to 5.5V  
IOL = 1.5mA  
Output “L” voltage *1  
VOL  
VOL  
VCC = 4.0 to 5.5V  
(Pin number1-4, 12-32)  
IOL = 1.0mA  
1.0  
2.0  
0.3  
VCC = 3.3 to 5.5V  
IOL = 15mA  
VCC = 4.1 to 5.5V  
IOL = 1.5mA  
V
V
Output “L” voltage  
(Pin number. 12 - 16)  
VCC = 4.1 to 5.5V  
Hysteresis  
(Pin number 12, 15, 17-26, 30)  
Hysteresis  
VT+ - VT-  
0.4  
0.5  
0.5  
V
VT+ - VT-  
V
(Pin number 26, 28)  
Hysteresis  
VT+ - VT-  
V
(Pin number 6)  
Input “H” current  
(Pin number 1-4, 12-32)  
Input “H” current  
(Pin number 6)  
IIH  
IIH  
IIH  
IIL  
VI = VCC  
VI = VCC  
5.0  
5.0  
μA  
μA  
μA  
μA  
μA  
μA  
uA  
Input “H” current  
(Pin number 9)  
VI = VCC  
4.0  
Input “L” current  
(Pin number 1-4, 12-32)  
Input “L” current  
(Pin number 6)  
VI = VSS  
-5.0  
-5.0  
IIL  
VI = VSS  
Input “L” current  
(Pin number 9)  
IIL  
VI = VSS  
-4.0  
0.1  
Icc  
1.0  
Power supply current  
STOP mode  
Document No. DER-S0026A  
11  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
6. Packaging Specification  
6-1. Outline  
With a basic packaging unit of 2000, TSC-40/IC is packaged for the number of 2000 and its multiple using  
damp-proof aluminum laminate bags (Basic packaging). If the delivery quantity is less than 2000 or not  
multiple of 2000, or the product can not be packaged with a unit of 2000, then no damp-proof packaging  
specification is applicable (Small group packaging).  
If packaged with small group packaging, the products may be dampened. Before packaging, the product  
shall take the baking process as specified in [Baking] defined in “TSC-40/IC Storage/Implementation  
Specification”.  
6-2. Notes on storage/handling  
(1) Handle the packages with care and avoid throwing and dropping them. Or, a large impact may be  
imposed, causing packaging material’s damage, broken package or bending lead.  
(2) Cardboard box may be deteriorated in its strength and deformed due to storage site’s humidity,  
stacking condition and storage duration. It is desirable to keep the storage under normal  
temperature/humidity (5 to 35 °C, 45 to 75%RH). For warehousing, follow the FIFO principle.  
(3) After unpacking, be careful in handling the product to avoid electrostatic breakdown.  
6-3. Basic packaging  
6-3-1. Packaging type  
Damp-proof packaging (Aluminum laminate bag)  
6-3-2. Packaging quantity specification  
Quantity per tray  
250  
Number of trays  
8 + 1(cover)  
Quantity per packages  
2000  
Desiccant  
Tray  
Product name label  
Aluminum laminate bag  
Humidity indicator  
Packaging label  
Packaging label  
Product name  
label  
Packaging box  
Document No. DER-S0026A  
12  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
6-3-3. Diagram for packaging box sizes  
L: 330 W: 152 D: 75 (mm)  
6-4. Small group packaging  
6-4-1. Packaging type  
General packaging (No damp-proof processing)  
6-4-2. Packaging quantity specification  
Quantity per tray  
250  
Number of trays  
1 to 8 +1(cover)  
Quantity per packages  
1 - 1999  
Number of trays: 1 to 8  
(Additionally, one dummy tray pl  
aced at the top for reinforcing)  
Air cap  
Desiccant  
Product name label  
Antistatic bag  
* No sizes specified for packaging box (Cardboard  
box) used for transportation.  
Document No. DER-S0026A  
13  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
6-5. Tray specification  
This tray is heat-proof type, allowing the heating with 125 °C for 24 hours. During heating/cooling process,  
however, bending may occur. In baking process, to minimize the bending, heat and cool the tray by placing  
it on a flat plate.  
6-6. Product name label specification  
DMC P/N: Product number (TSC-40/IC)  
QTY:  
DAC:  
Quantity  
DMC Control Number  
Document No. DER-S0026A  
14  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
7. Storage Specification  
7-1. Storage Conditions  
For storing the product until its implementation, it is recommended that the following storage conditions are  
applied:  
1. Before unpacking the damp-proof package (Aluminum laminate bag)  
Temperature and humidity:  
Duration:  
5 to 40 °C, 20 - 80%RH  
Two years or less  
2. After unpacking the damp-proof package (Aluminum laminate bag)  
For the storing duration after the damp-proof package is unpacked and before the implementation, it is  
recommended that the following storage conditions is to be applied:  
(1) Reflow method:  
One week or less under the ambient condition: 30 °C, 70%RH or less  
(2) Wave soldering method: One week or less under the ambient condition: 30 °C, 70%RH or less  
3. Temporary storage after damp-proof package is unpacked  
To store again temporarily the once unpacked and unused damp-proof package, it is recommended to  
pack it again into another damp-proof bag with desiccant within a shorter time after opened (Around 10  
minutes) as far as possible, and fold the bag’s opening, followed by sealing with adhesive material  
such as adhesive tape, then store it under the following conditions:  
Temperature, humidity:  
Duration:  
5 to 40 °C, 20 - 80%RH  
One month or less  
7-2. Baking  
If any condition among those 1 to 3 listed below is applicable, it is recommended to apply the baking as  
described below to dry the moisture the package absorbs.  
You may place the tray used for damp-proof packaging directly into the thermostatic chamber since the  
tray is heat-proof type. When placing into the chamber or after removing from it, to avoid deformation, cool  
the tray by placing it on the flat plate such as surface table.  
1. Any condition among 1 to 3 in [7-1. Storage condition] is unsatisfied  
2. Indicator’s 30% Humidity Check section changes the color to lavender or pink  
3. Blue color indicator of desiccant (Silica gel) changes to pink or white  
Baking method  
Temperature:  
Duration:  
125 °C  
20 to 24 hours  
Frequency:  
Four times or less (Upper limit: 96 accumulative hours)  
Document No. DER-S0026A  
15  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
8. Implementation Temperature Specification  
1. Reflow method (Infrared reflow, air reflow)  
Frequency:  
Three times or less  
Temperature:  
The following device surface temperature profile is recommended.  
260 °C max.  
255 °C or above, 10-16s max.  
220 °C or above, 60s max.  
175±15 °C  
1 to 4 °C/s  
110±30s  
Time  
Figure 1: Infrared reflow, air reflow temperature profile  
2. Wave soldering method (Flow soldering, solder dip method)  
Frequency:  
One time or less  
Temperature:  
Following temperature profile is recommended (Set the optimal preheat temperature  
according to the flux type)  
10s max. (Primary + Secondary flow  
passage duration)  
260 °C max.  
80 to 150 °C (Package surface temperature)  
Time  
Figure 2: Wave soldering temperature profile  
3. Soldering iron (Manual soldering)  
Soldering bit’s temperature:  
370 °C or lower  
Soldering time:  
Five seconds or less/terminal  
Document No. DER-S0026A  
16  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
9. Terminal Pin Specification  
Base material  
Coat  
:Cu  
:Sn-1.5%Cu  
:5um or above  
Thickness of coat  
10. Cleaning  
In case of cleaning boards with solvents after soldering, following items should be taken attention.  
*Administrative guidance and regulation.  
*Residual ionic (non ionic) contamination.  
*Solvent resistance of parts.  
Document No. DER-S0026A  
17  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
11. Changes and improvements  
11-1. Version history  
§
TSC-40/IC  
Ver0.1 (October 3, 2007)  
Draft release  
Ver0.2 (December 10, 2007)  
5-3. Timing requirement  
External clock timing  
Clerk mistake was corrected.  
Input cycle 500ns 166ns  
Clock pulse 200ns 70ns  
6-6. Product name label specification  
Ver0.3 (January 21, 2008)  
“Pb Free” was added.  
Circuit Diagram 5-Wire Resistive Touch Screen  
Corrected the 15th-Pin (SEL3/EEP_CLK) to connection with Vcc via resistance.  
Ver1.0 (March 13, 2008)  
First release  
(Change from ver0.3)  
1-4. General specification  
Input response time was added.  
3. Pin functions Detail information was added in 22, 23, 24 pin.  
9. Terminal Pin Specification was added.  
Document number was added.  
Circuit Diagram  
Part number was added. (Rev 2)  
Ver1.1 (June 30, 2008)  
5-2. Recommended operational conditions (TTL input level selected) was deleted.  
Ver1.2 (July 2, 2008)  
1-4. General specification  
Power supply voltage DC 2.4V to 5.5V DC 3.3V to 5.5V  
Document No. DER-S0026A  
18  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
12. Warranty  
12-1. Warranty Period  
§ The warranty period is limited to 1 year from the date of shipping. The warranty for the initial defection  
such as appearance defection is limited to 1 month.  
§ Any defected parts under proper use will be examined by the supplier and replaced by the new parts if  
the defection is considered to be caused by the supplier.  
§ The replacement is subject to be included in the next lot.  
12-2. Warranty Target  
§ The warranty only covers the product itself and does not cover any damage to others caused by using  
this product. Onsite repair or replacement is not supported.  
§ We will do our best for delivery problem and product defections, but the warranty for the production line  
is not covered.  
12-3. Warranty Exceptions  
Following conditions are not covered with the warranty and subject to charge.  
§ Any malfunctions and damages during transportation and transfer by the user.  
§ Any malfunctions and damages caused by a natural disaster or a fire.  
§ Any malfunctions and damages caused by static electricity  
§ Any malfunctions and damages caused by the failure of the associated equipment.  
§ If the product is remodeled, disassembled or repaired by the user.  
§ If the product is glued onto the equipment and uninstalled.  
§ Any malfunctions and damages caused by an improper usage and handling against the specifications  
and notes.  
Document No. DER-S0026A  
19  
Version 1.2 ©2008 DMC Co., Ltd.  
 
TSC-40/IC Product Specification  
13. Notes on use  
13-1. Overall handling  
§ When using the product, do not place it close to, or make it contact with, the conductive materials such  
as metal.  
§ Do not touch the metal part in the product directly with your hands. Or, it may be destructed by the static  
electricity. If you contact, or may contact, it directly with your hand, prepare in advance the measure  
against static electricity.  
§ To store the product, use an appropriate packing box and keep the storage temperature range with no  
overload on it.  
§ In using the product or storing it, avoid the following conditions:  
- Conditions where water is, or may be, attached to the product.  
- Conditions where condensation takes place, or may take place.  
- In the ambience of organic solvent or acidity or contact, or where the product contacts them.  
§ Do not alter or disassemble the product.  
13-2. Others  
§ This specification may be changed for improvement without prior notices.  
§ No liabilities are taken by us for any damage caused by use of this product.  
§ This product intends to be used for the standard applications (e.g. office equipment and OA devices,  
industrial use, communication devices, household equipment). Avoid its use where failure or malfunction  
directly may affect the human body or special applications where extremely high reliability is required  
(e.g. airline and space industries, nuclear controls, medical use for life-sustaining).  
§ Semi-conductor devices may fail in a certain possibility. Keep the safety design in your mind so that  
possible failure in this product shall not cause physical accidents such as injury and death, fire and other  
social damages.  
TSC-40/IC Product Specification  
Version 1.2: Issued at July 2, 2008  
©2008 DMC Co., Ltd.  
This document is allowed to redistribute but no alteration, part or all, is prohibited.  
9F Kanda Sent-Building 1-2-4, Yushima, Bunkyo-ku, Tokyo, 113-0034 Japan  
Phone: +81-3-5209-7131 (Japanese), 7135 (English) Fax: +82-3-5209-7130  
Document No. DER-S0026A  
20  
Version 1.2 ©2008 DMC Co., Ltd.  
 
 
 
 

AEG Cooktop 231GR M RU 949600674 User Manual
Agilent Technologies TV Converter Box E4443A3HZ 67GHZ User Manual
Allied Telesis Network Card AT AR040 10 User Manual
Allied Telesis Network Router AT AR441S User Manual
Amana Clothes Dryer LED250 User Manual
American Standard Hot Tub 6060028WC User Manual
American Standard Indoor Furnishings 0419111 User Manual
Atlona Camcorder AT HD V42M User Manual
Axis Communications Security Camera P1405 E User Manual
BK Stereo Receiver AVR202 Plus User Manual