Acer Computer Monitor AC 711 User Manual

Table of Contents  
Important Safety Instructions....................................................................................................... 1  
Federal Communications Commission........................................................................................ 4  
Connecting the Monitor and Swivel Base.................................................................................... 2  
Removing the Monitor and Swivel Base ...................................................................................... 2  
Introduction.................................................................................................................................... 3  
Installation...................................................................................................................................... 3  
User Controls.................................................................................................................................. 4  
OSD Function Description............................................................................................................ 4  
OSD Icon Summary....................................................................................................................... 5  
Specification.................................................................................................................................... 5  
Troubleshooting............................................................................................................................. 7  
Important Safety Instructions  
1. Please read these instructions thoroughly.  
2. Please keep this guide for future use.  
3. Please disconnect the device from the main power supply before cleaning. Do not use any liquids or aerosol  
sprays to clean this device. Use a clean dampened cloth in stead.  
4. To avoid damaging the device, only use factory-approved accessories.  
5. Protect the device against moisture.  
6. In order to set up the device, first place it on a stable surface. Tipping it over or dropping can harm the  
monitor and cause injuries. Please follow the setup instructions of the manufacturer while setting up your  
monitor.  
7. The ventilation openings are used for air circulation to protect the device against overheating.  
8. When connecting the device, obey the maximum connected load values of the main power supply.  
9. The wall socket must be equipped with a non-fused grounded conductor contact for electrical safety.  
10. The power cable must be laid in such a way nobody can trip over it. Please do not place any objects on the  
cable.  
11. Follow all instructions and warning remarks that are printed on the device.  
12. If the device will not be used for a long period of time, please disconnect it from the main power supply to  
avoid power surge damage such as lightning.  
13. Make sure no sharp objects or liquids enter the device via its air circulation openings. This could result in a  
fire or an electric shock.  
14. Never open the device casing yourself, there are no user serviceable parts inside. Only authorized technical  
service personnel should open the casing of this device.  
15. If any of the following conditions occur, the device must be disconnected from the main supply, and be  
checked by a qualified service center:  
a- Power cable or power plug are damaged;  
b- Liquid has entered the device;  
c- The device was exposed to moisture;  
d- The device does not operate according to the user’s guide, or you do not achieve any improvement with  
the aid of this guide;  
e- The device has been dropped and/or the casing is damaged;  
f- The device shows obvious signs of a defect.  
16. Use only approved original spare parts, or parts in accordance with the original parts, for repairs. The use of  
incorrect/unauthorized spare parts may cause further damage.  
17. Please contact your service center for any questions regarding service and repairs to guarantee the device’s  
performance and reliability.  
18. The power socket must be installed near the equipment to be easily accessible.  
1
 
Introduction  
Congratulations on your purchase of this new high performance 17” Monitor. Using state-of-the-art  
electronics, this monitor supports a 1280 x 1024 resolution. The on-screen display allows you to  
customize the display settings to suit your individual taste.  
Features  
Ø17-inch monitor with a large, viewable screen  
for comfortable viewing.  
ØOSD user controls for easy and accurate  
adjustment of the screen image.  
ØEnergy Star compliant for reduced power  
consumption.  
Package Overview  
Please make sure the following items are in the packing it was shipped in, and found in good  
working condition:  
n 17” Monitor  
n Power Cord  
n Tilt and Swivel Base  
n This Users manual  
Please contact your dealer or nearest service centers if any of the above items is missing or damaged.  
Installation  
1. Connect the monitor signal cable  
1
to the  
15-pin mini D-sub (VGA) on the back of  
the computer.  
2. Connect the power cord  
to the power  
connector on the back panel of the monitor,  
then plug the other end into an electrical  
outlet that is easily accessible, and close to  
the monitor.  
3. First turn on the power of the computer,  
then that of the monitor.  
4. Adjust the tilt of the swivel base for  
maximum viewing comfort.  
The installation of your monitor is now  
complete.  
3
 
User Controls  
1.  
3.  
Power Switch  
Turns the monitor on  
2.  
4.  
Power LED Indicator  
LED color  
Green  
Status  
On  
Amber  
Sleep  
Select Button  
Backward and Forward Buttons  
·
·
Launches On -Screen Display  
Make sure the select functions  
or adjustments  
·
Backward button (left arrow) moves  
backward through menu options or  
decreases adjustment levels.  
·
Forward button (right arrow)  
moves forward through menu  
options or increases adjustment  
levels.  
·
Exit menus and On-Screen  
Display  
OSD Function Description  
1. Press the  
key to display the OSD menu.  
2. To select a function, press the  
the desired function is highlighted.  
and  
keys until  
3. Press the  
key to choose the function.  
4. Use the  
and keys to increase or decrease the  
parameter level of the setting.  
5. Press the  
6. Select the  
key to save the new setting.  
icon if you want to exit the OSD  
key once.  
function, and then press the select the  
4
 
OSD Icon Summary  
Icon  
Function  
Brightness  
Contrast  
Function Description  
Adjusts display brightness  
Adjusts display contrast  
H. Size  
H. Position  
V. Size  
Increases and decreases screen width  
Shifts display image right or left  
Increase and decrease screen height  
V. Position  
Pin. Balance  
Pincushion  
Parallelogram  
Trapezoid  
Rotation  
Shifts display image up or down  
Adjusts each side of Pincushion  
Adjusts concave and convex portion of pincushion effect  
Adjusts the tilt of the display sides to the left or right  
Adjusts the top and bottom display widths  
Adjusts the rotation of the display clock or anti-clockwise  
Adjusts the warmth of the displayed colors  
Resets to default values  
Color Temp.  
Reset  
Degauss  
Demagnetizes the screen to reduce color impurities  
Exit  
Exits the OSD menu  
Specification  
Screen  
Size  
17” CRT  
Dot Pitch (mm)  
0.27  
Surface  
Viewable Image Area  
Non –glare  
16.14” (41.0 cm)  
Input Signal  
Video Sy nc.  
RGB Analog 0.7Vp -p/75 Ohm  
a. Separate H/V,TTL(+/-)  
b. Composite H+V,TTL(+/-)  
Scanning Frequency  
Horizontal (KHz)  
Vertical (Hz)  
30-70  
50-160  
Max. Resolution  
1280 x 1024  
Signal Cable  
Power  
15-pin mini D-sub  
Consumption  
Power Supply  
Power Management  
Max. 75 W  
100 - 240VAC (W/I CE Mark) 50/60Hz  
Complies with EPA Energy Star ,VESA,  
Nutek  
Display Modes  
Operating  
Relative Humidity  
Dimensions (L x W x H) 419 x 405 x 427 (mm)  
Weight Unpacked  
Preset  
By User  
6
14  
Operating Temperature 0-40°C  
10-90 %  
14.9 Kgs (32.85 lbs)  
5
 
Packed in box  
16.8 Kgs (37.04 lbs)  
6
 
Troubleshooting  
Please refer to the following solutions for the failure symptoms that occur the most frequent. If the  
symptom remains after trying these suggested solutions, please contact your local authorized service  
center.  
Problem: Power LED is not lit when monitor is powered on.  
@Check to make sure that the power cord is connected properly.  
@Make sure that the extension cord or the surge protector is turned on if the monitor is plugged  
into a power extension cord or a surge protector.  
Problem: No display appears on screen.  
@Make sure that the computer switch is in the “On” position.  
@Make sure that the video cables D-shaped connector is properly connected to the video  
adapter port on the back of the PC.  
@Check to make sure that the brightness and contrast controls are not turned to their dimmest  
position.  
Problem: Display image is either flickering or unstable.  
@Make sure that the video cable’s D-shaped connector is connected properly to the video  
adapter port on the back of the PC.  
Problem: Image is bouncing or in a wave pattern.  
@Move any electrical devices that can cause interference away from the monitor.  
(Note: Please refers to the FCC statement at the beginning of the manual for more details on  
display interference.)  
7
 

3M Respiratory Product 7190 User Manual
Aarrow Fires Stove AFS1221 User Manual
Agri Fab Lawn Aerator 45 0299 User Manual
Alamo Lawn Mower 02981992P User Manual
Allstar Products Group Garage Door Opener 8822 User Manual
Aluratek Digital Photo Keychain ADPF01F User Manual
Amana Clothes Dryer LED250 User Manual
Asus Network Card CUVL VM User Manual
Bakers Pride Oven Oven EB User Manual
Beko Oven 4200 SA User Manual