Air Oasis Air Cleaner Induct 9 User Manual

Troubleshooting Guide  
Problem  
Reason  
Solution  
Unit does not turn on.  
1. Power Cord  
1. Check to make sure  
power cord is plugged  
in.  
2. Switch  
2. Check to make sure  
switch is in the on posi-  
tion.  
3. AHPCO™ Cell  
3. Check to make  
sure UV lamp within  
AHPCO™  
Cell  
in  
plugged in completely.  
Induct 9  
Owner’s  
Manual  
Unit is not reducing  
odors.  
1. Defective AHPCO™  
Cell  
1. Check to make sure  
the AHPCO™ Cell has  
a blue glow. If you see  
no glow or the glow has  
turned to a purple color,  
contact Air Oasis.  
This Manual Includes:  
• Warranty  
• Safety Warnings  
• Installation Instructions  
• Operating Instructions  
• Replacement Directions  
• Troubleshooting Tips  
irway Blvd  
Amarillo, TX 79118  
Before operating this unit or replacing the AHPCO™  
Cell carefully read the contents of this manual.  
Toll-Free: 1-800-936-1764 Fax: 1-806-373-7799  
Copyright© 2006 Air Oasis All Rights Reserved  
 
Induct 9 Installation Instructions  
Step 1  
Tear out the  
cutout template and  
trace the circle onto  
the ductwork and cut  
hole .  
Step 2  
Remove the  
wax paper from the  
gasket.  
 
If you do not have a hole saw tear this page off and cut the  
circle out. Then place on the ductwork in desired position  
and trace the rectangle. Drill holes as indicated and then  
use a jig saw or metal cutting snips to cut out the circle.  
Step 3  
Insert unit into  
pre-cut hole.  
Cut Out  
Step 4  
Drill the metal  
tapping screws in to  
hold unit in place.  
 
Read all instructions carefully before operating  
your air purifier.  
Step 4  
Plug the power cord into an electrical outlet. You may optionally have an  
electrician wire the air purifier to your HVAC unit so that the air purifier only  
operates when your HVAC fan is running. Once the unit is plugged in the  
indicator light should glow to indicate the AHPCO Cell is working properly.  
Table of Contents  
Safety Instructions and Cautions  
Table of Contents  
1
2
3
Warranty  
Maintenance and Customer Service  
Placement and Operation  
Cleaning  
4
4
AHPCO™ Cell Replacement  
Step 1  
4
CAUTION: Before attempting to service the Air Oasis unit, be sure the  
power is off and unplugged.  
AHPCO™ Cell Replacement  
Troubleshooting Guide  
5-6  
7
Remove three (3) screws at the top of  
the aluminum face plate. Then slide  
the face plate up and off.  
Step 2  
Unplug the four pin lamp connec-  
tors and fiber optic cords from the  
AHPCO Cell.  
5
2
 
Warranty  
Maintenance and Customer Service  
If you require any additional information or have problems with your Air Oasis ap-  
pliance, you may call Air Oasis customer service at:  
1-800-936-1764  
Air Oasis gives you the following limited warranty for this product only if it was origi-  
nally purchased for residential or commercial use but, not resale from Air Oasis or  
an Air Oasis Authorized Retail Dealer.  
Please have your serial and model numbers, found on bottom of the unit, handy  
when calling.  
Air Oasis will repair or replace, free of charge, to the original purchaser, any part  
that is found to be defective in material or workmanship within three (3) years of  
the date of purchase.  
Save your sales receipt to show if your Air Oasis appliance should ever need any  
warranty service.  
This limited warranty covers the replacement of a defective AHPCO Cell for a pe-  
riod of three years.  
Installation and Operation  
This limited warranty does not apply to any part subjected to accident, abuse, cer-  
tain commercial uses, alteration, misuse, damage caused by act of God, the use  
of voltages other than indicated on the label displayed on this product or service of  
this product by anyone other than Air Oasis.  
It’s strongly recommended that only a licensed electrician  
or HVAC installer properly install this unit.  
The purifiers can be installed on either the return or supply side of the  
plenum.  
Air Oasis does not authorize any person or representative to assume or grant any  
other warranty obligation with the sale of this product.  
Step 1  
Air Oasis’ limited warranty is valid only if you retain proof of purchase from Air Oa-  
sis or an Air Oasis Authorized Retail Dealer for this product. If you purchase this  
product from any other source, your purchase is “AS IS”, which means Air Oasis  
grants you no warranty, and that you, not Air Oasis, assume the entire risk of the  
quality and performance of this product, including the entire cost of any necessary  
servicing or repairs of any defects.  
Cut a 2” hole in the plenum using a hole  
saw. Make sure the hole is centered so  
that no part of the mounting plate is hang-  
ing off the edges of the plenum when the  
probe is inserted.  
Air Oasis’ liability for damages to you for any costs whatsoever arising out of this  
statement of limited warranty shall be limited to the amount paid for this product  
at the time of original purchase, and Air Oasis shall not be liable for any direct,  
indirect, consequential or incidental damages arising out of the use or inability to  
use this product.  
Step 2  
Insert the probe into the 2” hole until the  
back mounting plate is flush against the  
plenum surface. We recommend mounting  
the unit with the rectangular side facing ei-  
ther left or right, but not down or up.  
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING  
IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTIC-  
ULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD,  
AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AF-  
TER THIS PERIOD.  
Step 3  
Some states do not allow limitations on the duration of implied warranties, so the  
above limitation may not apply to you. This warranty gives you specific legal rights,  
and you may also have other rights which vary from state to state.  
Attach the mounting plate to the plenum  
surface using sheet metal screws. There  
are predrilled holes on the mounting plate  
that can be used as a guide. It’s recom-  
mended to seal the edges of the mounting  
plate using aluminum insulation tape.  
To obtain warranty service and return authorization number, contact us at:  
PH: (800) 936-1764, FAX: (806) 373-7799 or E-mail to [email protected]  
NOTE: All returned packages that do not have an RMA# will be refused.  
3
4
 

Acer Computer Monitor 718 User Manual
Acer Personal Computer Veriton 3500 User Manual
Acer Projector PD523P User Manual
Acesonic Karaoke Machine DKR 510 User Manual
Acnodes Computer Monitor PMW6220 User Manual
ADC Network Card WMX 3000 User Manual
Agilent Technologies Automobile Parts E1465A User Manual
Alpine DVD Player Alpine DVD Entertainment System User Manual
ATI Technologies Computer Hardware 117 70104 30 User Manual
BC Speakers Speaker 10PS26 User Manual