Aiwa Car Stereo System CDC Z127 User Manual

OPERATING INSTRUCTIONS  
MANUAL DE INSTRUCCIONES  
MODE D’EMPLOI  
CDC-Z127  
YU  
STEREO CAR CD RECEIVER  
RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA  
AUTOMOVIL  
ENGLISH  
ESPAÑOL  
FRANÇAIS  
OWNER’S RECORD  
For your convenience, record the model number and  
serial number (you will find them on the bottom side of  
your set) in the space provided below. Please refer to  
them when you contact your AIWA dealer in case of  
difficulty.  
Model No. CDC-Z127  
Serial No.  
8C-KCH-901-01  
011120ATM-OX  
 
1
2
Press SEL repeatedly to select the mode to be  
adjusted.  
Pressing SEL cycles through the modes. The  
selected modes indicator flashes.  
BASIC OPERATION,  
AUDIO AND CLOCK  
ADJUSTMENT  
Turn AUDIO CONTROL to increase/decrease the  
level or to select on/off for the selected mode.  
PWR/MUTE  
SEL  
Note  
AUDIO CONTROL  
Adjust the level or select on/off within 5 seconds, or the  
selected mode will return to previous state.  
Aligning the source levels  
(Source Level Adjuster)  
i
/
k
DISP SRC  
Volume may vary each time you change the source  
mode. In this case, you can align each source modes  
volume to almost the same level.  
BAND  
Turning the unit on/off  
1
2
3
PressSRCorBANDrepeatedlytoselectthedesired  
mode.  
Press PWR/MUTE to turn on the unit. The unit also  
turns on when you insert a CD.  
Press and hold PWR/MUTE until the unit turns off.  
Press DISP while pressing SEL.  
LA 0appears in the display.  
Turn AUDIO CONTROL to adjust the level.  
Note  
Mostoperationsdescribedinthismanualrequirethe  
unit to be turned on before starting the operation,  
unless explicitly stated otherwise.  
Note  
Adjust the level within 5 seconds, or the selected mode  
will be canceled.  
Changing the source mode  
Restoring the factory settings  
1
Press SRC.  
1
2
Turn off the unit.  
Pressing SRC cycles through source modes in the  
following order:  
Press and hold DISP until LA --appears in the  
display.  
FM1 (FM2/FM3/AM1/AM2) CD* AUX  
Note  
You can restore the factory settings only for VOL,  
BASS, TRE, BAL, FAD, and H-BASS, and aligned  
source volume levels.  
* CDdoes not appear in the display when there is no  
CD in the unit.  
Adjusting the volume  
Muting button beep sounds  
1
Turn AUDIO CONTROL.  
VOL (volume) indicator flashes.  
1
2
Turn off the unit.  
Press and hold SEL until bEEPappears in the  
display.  
Muting the sound  
3
4
TurnAUDIOCONTROLtoselecton(levelindicators  
appear) or off (level indicators disappear).  
Press SEL.  
1
Press PWR/MUTE briefly.  
MUTE indicator flashes.  
To restore volume, briefly press PWR/MUTE again.  
Adjusting sound  
You can select the following modes for adjusting sound  
depending on the music you listen to: BASS (low  
frequencies), TRE (high frequencies), BAL (left/right),  
FAD (front/ rear) and H-BASS (high bass).  
ENGLISH 2  
 
Setting the clock  
Monaural mode  
When signals become weak, or reception becomes  
poor, the unit automatically switches to Monaural mode  
to reduce noise.  
1Press and hold DISP until the clock indicator  
flashes in the display.  
2Press i (to set hour) or k (to set minute), and  
then turn AUDIO CONTROL.  
Local mode  
Local mode allows you to tune in only to strong stations  
during Seek Tuning.  
3Press DISP.  
1
Press LO before you start seek tuning.  
LOappears in the display.  
Displaying the clock  
To return to Distant mode, press LO again.  
LOdisappears and the unit tunes in to all receivable  
stations.  
1
Press DISP.  
To return to the former display, press DISP again.  
Using preset stations  
RADIO OPERATION  
Youmustpresetstationsbeforeyoucantuneinastation  
using preset station number buttons.  
Tuning in to a station  
(Seek/Manual Tuning)  
LO  
PS/A.ME  
/k  
BAND  
i
Preset station buttons 1 to 6  
BAND  
i
/k  
Stereo indicator Local indicator  
Preset station number  
Presetting stations automatically  
(Auto Memory)  
Band indicator Frequency indication  
1
Press BAND repeatedly to select the desired band  
(FM1, FM2, FM3, AM1, or AM2).  
1
Press BAND repeatedly to select the desired band  
(FM1, FM2, FM3, AM1, or AM2).  
Press and hold PS/A.ME until automatic presetting  
starts.  
2* Press i (to move to higher frequencies) or k (to  
move to lower frequencies) to tune in to a station.  
STappears in the display when an FM station is  
broadcasting in stereo, and receiving conditions are  
good.  
2
The unit automatically stores up to 6 stations for  
each band.  
After completion of automatic presetting, the unit  
tunes in to the station stored on preset station  
button 1.  
*Seek Tuning and Manual Tuning  
Press and hold i or k until seek Tuning starts.  
Theunitlocatesastationautomatically(SeekTuning).  
Press i or k repeatedly to search for a desired  
station while increasing or decreasing the frequency  
step by step (Manual Tuning).  
Tocancelautomaticpresetting,pressPS/A.MEagain.  
Checking the preset stations (Preset Scan)  
1
Press PS/A.ME briefly.  
To stop Seek Tuning, press i or k again.  
Each preset station will be tuned in for 5 seconds in  
order.  
To cancel Preset Scan, press PS/A.ME again or any  
preset station button.  
3 ENGLISH  
 
Presetting stations manually  
(Manual Memory)  
Labeled-side up  
1
Press BAND repeatedly to select the desired band  
(FM1, FM2, FM3, AM1, or AM2).  
2
Press i or k to tune in to a desired station (see  
Tuning in to a stationas well for another tuning  
method).  
Track number  
3
Pressandholdthedesiredpresetstationbuttonuntil  
the unit beeps.  
Note  
A newly preset station replaces the station on the same  
band that was previously stored on that preset station  
button.  
CD indicator Elapsed playing time  
To  
Press  
Tuning in to a preset station  
Eject a CD  
z
1
2
Press BAND repeatedly to select the desired band  
(FM1, FM2, FM3, AM1 or AM2).  
Skip to the next track  
t
r
Go back to the beginning  
of the current track  
Each extra press skips  
backward one extra track  
Press the preset station button on which the desired  
station is stored.  
Active tuning reception control (ATRC)  
The unit automatically suppresses FM noise caused by  
vehicle movement, and maintains sound quality.  
Locate a specific point in Press and hold r or  
a track  
t until you find the  
point.  
Note  
CD PLAYER OPERATION  
When you play a CD that is already inserted, CD play  
starts at the point where it stopped the previous time.  
A newly inserted CD starts from the first track.  
A CD-R or CD-RW may take some time to start playing  
back, but this is not a malfunction.  
If a CD-R or CD-RW with no data or incompatible data  
is inserted, E03will appear in the display. The unit  
cannot play such discs.  
Playing a CD  
You can play CDs, CD-Rs and CD-RWs using the  
procedure described below.  
SRC  
z
Intro Play  
You can locate a desired track by monitoring the first 10  
seconds of all the tracks on a CD.  
1
Press INT during CD play.  
INT RNDM  
REP 1  
SCANappears in the display.  
r
/t  
2
Press INT again when the desired track is played.  
The unit returns to normal CD play.  
1
Insert a CD.  
CDappears in the display.  
One track Repeat Play  
CD play starts.  
If a CD is already inserted, press SRC repeatedly to  
select CD play mode.  
You can play a track repeatedly.  
1
Press REP1 during CD play.  
In normal play, when the last track finishes, the unit  
returns to the first track and continues to play.  
REPEAT1appears in the display.  
To cancel One track Repeat Play, press REP1 again.  
ENGLISH 4  
 
Random Play  
You can play all the tracks in random order.  
TROUBLESHOOTING  
1
Press RNDM during CD play.  
RANDOMappears in the display.  
Error code  
In the following cases the corresponding error code  
indication appears. Follow the suggestions below to  
solve such problems. If the error code indication does  
not disappear, consult an AIWA service center.  
To cancel Random Play, press RNDM again.  
Note  
During Random Play, pressing r allows you to skip  
only to the beginning of the current track, not to the  
previous track.  
E03 Focuserror.CheckthattheCDisloadedproperly  
(right side up, etc.), and the CD contains valid  
data.  
Reset button  
AUXILIARY EQUIPMENT  
IfaCDdoesnotoperateproperly, presstheresetbutton  
with a pointed object such as a pencil, etc. Note that all  
your settings will be erased if this button is pressed.  
Listening to a cassette/MD/MP3 portable  
player or other equipment  
Reset button  
Youcanlistentoequipmentconnectedtotheunit. Refer  
to the operating instructions for the corresponding  
equipment for more detailed information.  
Be sure to remove inserted CDs to prevent possible  
damage to the unit before connecting the equipment.  
MAINTENANCE  
SRC  
AUX jack  
Cleaning the front panel  
Wipe the surface with a soft, dry cloth. Do not use liquid  
cleaners or aerosol cleaners.  
1
2
Connectacassette/MD/MP3portableplayerorother  
equipment to the units AUX jack (3.5 mm dia.).  
Press SRC repeatedly until AUXappears in the  
display.  
During AUX mode, the clock display appears.  
OTHER FUNCTION  
AUDIO  
SEL  
CONTROL  
Setting the dimmer of the display  
1
2
Press and hold SEL until Dappears in the display.  
Turn AUDIO CONTROL to select D 0 (bright)or D  
1 (dimmed).”  
5 ENGLISH  
 
SPECIFICATIONS  
RADIO SECTION  
(FM)  
Frequency Range: 87.5 MHz 108 MHz  
Usable Sensitivity: 12.7 dBf  
50 dB Quieting Sensitivity: 17.2 dBf  
IF Rejection: 100 dB  
Frequency Response: 30 Hz 15,000 Hz  
S/N Ratio: 70 dB  
Stereo Separation: 35 dB at 1 kHz  
Alternate Channel Selectivity: 90 dB  
Capture Ratio: 3 dB  
(AM)  
Frequency Range: 530 kHz 1,710 kHz  
Usable Sensitivity: 30 µV (30 dB)  
CD SECTION  
Frequency Response: 17 Hz 20 kHz +0/3 dB  
Dynamic Range: More than 85 dB  
Channel Separation: More than 60 dB  
S/N Ratio: More than 90 dB  
Wow/Flutter: Unmeasurable  
AUDIO SECTION  
Max. Power Output:45 W × 4 channels  
AUX input  
Input sensitivity (load impedance) AUX: 300 mV  
(10 k)  
GENERAL  
Power-Supply Voltage: 14.4 V (11 to 16 V  
allowable), DC, negative ground  
Load Impedance: 4 Ω  
Tone Control:  
Bass ± 10 dB at 100 Hz, Treble ± 10 dB at 10 kHz  
Preamp Output Voltage (load impedance): 2.2 V  
(10 k)  
Installed size: 182 (W) × 53 (H) × 155 (D) mm  
(7 1/4 (W) × 2 1/8 (H) × 6 1/8 (D) inches)  
Specifications and external appearance are subject to  
change without notice due to product improvement.  
REAR PANEL  
For details, refer to the separate INSTALLATION AND  
CONNECTIONS.  
ENGLISH 6  
 
Printed in Indonesia  
 

3Com Digital Camera iCV 01a User Manual
3M Microphone BK4936 User Manual
Abocom Network Card PLE0085I User Manual
Aiphone Home Security System AI 900 User Manual
Aiphone Thermostat PAA 100F User Manual
Aiwa Stereo System NSX MTD9 User Manual
American Standard Hot Tub T038990 User Manual
Atlona Stereo Amplifier AT HD V116 User Manual
Audiovox Automobile Alarm PRO9801 User Manual
Behringer Music Pedal EM600 User Manual