Alliance Laundry Systems Speaker 9001889R7 User Manual

Washer-Extractors  
Cabinet Freestanding  
WE-8 Computer  
Keep These Instructions for Future Reference.  
(If this machine changes ownership, this manual must accompany machine.)  
Part No. 9001889R7  
July 2011  
 
WARNING  
Failure to install, maintain, and/or operate this machine according to the manufacturer's  
instructions may result in conditions which can produce bodily injury and/or property  
damage.  
W030  
NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all  
possible conditions and situations that may occur. It must be understood that common sense, caution, and  
carefulness are factors which cannot be built into these washers. These factors MUST BE supplied by the  
person(s) installing, maintaining, or operating the washer.  
Always contact the distributor, service agent, or the manufacturer about any problems or conditions you do not  
understand.  
9001889  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
1
 
Introduction.........................................................................................  
3
Table of  
Contents  
Programming ......................................................................................  
Setup of the Chemical Hold Feature  
4
(Version 1.11 and later ONLY)......................................................  
7
Pre-Programmed Cycles .................................................................... 30  
Inverter Drive Error Codes............................................................... 56  
© Copyright 2011, Alliance Laundry Systems LLC  
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any  
means without the expressed written consent of the publisher.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
2
 
Introduction  
Model Identification  
Information in this manual is applicable to these  
models:  
HX018PVQM7 HX18PVXU6  
SX18PVQU6  
UX018PVQM7 UX18PVPA7  
UX018PVXA7 UX18PVPU6  
UX018PVXM7 UX18PVQA6  
UX18PVXA6  
UX18PVXA7  
UX18PVXM6  
UX18PVXM7  
HX018PVXM7 SX018PVPA7 SX18PVXM6  
HX18PVQM6 SX018PVQM7 SX18PVXM7  
HX18PVQM7 SX018PVXM7 SX18PVXU6  
UX18PVNA6  
UX18PVQA7  
18  
HX18PVQU6  
HX18PVXM6 SX18PVQM6  
HX18PVXM7 SX18PVQM7  
SX18PVPA7  
UX018PVNA7 UX18PVNA7  
UX018PVPA7 UX18PVNU6  
UX018PVQA7 UX18PVPA6  
UX18PVQM6 UX18PVXU6  
UX18PVQM7  
UX18PVQU6  
HX025PVQM7 HX25PVXU6  
HX025PVXM7 SX025PVQM7 SX25PVXU6  
SX25PVXM7  
UX025PVXM7 UX25PVQA6  
UX25PVNA6 UX25PVQA7  
HX25PVQM6 SX025PVXM7 UX025PVNA7 UX25PVNA7  
UX25PVXM6  
UX25PVXM7  
UX25PVQM6 UX25PVXU6  
UX25PVQM7  
HX25PVQM7 SX25PVQM6  
HX25PVQU6 SX25PVQM7  
HX25PVXM6 SX25PVQU6  
HX25PVXM7 SX25PVXM6  
UX025PVPA7 UX25PVNU6  
UX025PVQA7 UX25PVPA6  
UX025PVQM7 UX25PVPA7  
UX025PVXA7 UX25PVPU6  
25  
33  
35  
UX25PVQU6  
UX25PVXA6  
UX25PVXA7  
UX33PVNA7  
UX33PVPA7  
UX33PVQA7  
UX33PVQM7 UX33PVXA7  
UX035PVQM7 UX35PVPA7  
UX035PVXA7 UX35PVPU6  
UX035PVXM7 UX35PVQA6  
UX33PVXM7  
HX035PVQM7 HX35PVXU6  
SX35PVQU6  
UX35PVXA6  
UX35PVXA7  
UX35PVXM6  
UX35PVXM7  
HX035PVXM7 SX035PVNM7 SX35PVXM6  
HX35PVQM6 SX035PVQM7 SX35PVXM7  
HX35PVQM7 SX035PVXM7 SX35PVXU6  
HX35PVQU6  
HX35PVXM6 SX35PVQM6  
HX35PVXM7 SX35PVQM7  
UX35PVNA6  
UX35PVQA7  
SX35PVNM7  
UX035PVNA7 UX35PVNA7  
UX035PVPA7 UX35PVNU6  
UX035PVQA7 UX35PVPA6  
UX35PVQM6 UX35PVXU6  
UX35PVQM7  
UX35PVQU6  
UX40PVNA7  
UX40PVPA7  
UX40PVQA7  
UX40PVQM7 UX40PVXA7  
UX40PVXM7  
40  
55  
HX055PVNU7 HX55PVQU7  
HX055PVQU7 HX55PVXU6  
HX055PVXU7 HX55PVXU7  
HX55PVNU6  
HX55PVNU7  
HX55PVQU6  
SX055PVXU7 SX55PVQU7  
SX55PVNU6  
SX55PVNU7  
UX055PVXU7 UX55PVQU7  
SX55PVXU6  
SX55PVXU7  
UX55PVNU6  
UX55PVNU7  
UX55PVXU6  
UX55PVXU7  
SX055PVNU7 SX55PVPU6  
SX055PVPU7 SX55PVPU7  
SX055PVQU7 SX55PVQU6  
UX055PVNU7 UX55PVPU6  
UX055PVPU7 UX55PVPU7  
UX055PVQU7 UX55PVQU6  
HX075PVNU7 HX75PVPU7  
HX075PVPU7 HX75PVQU6  
HX075PVQU7 HX75PVQU7  
SX075PVQU7 SX75PVQU7  
SX75PVNU6  
SX75PVNU7  
UX75PVNU7  
UX075PVNU7 UX75PVPU6  
UX075PVPUU UX75PVPU7  
75  
HX75PVNU6  
HX75PVNU7  
SX075PVNU7 SX75PVPU7  
SX075PVPU7 SX75PVQU6  
X075PVQU7  
UX75PVNU6  
UX75PVQU6  
UX75PVQU7  
HX100PVNU6 HX100PVQU6 SX100PVNU7 SX100PVQU7 UX100PVPU6 UX100PVQU7  
HX100PVNU7 HX100PVQU7 SX100PVPU7 UX100PVNU6 UX100PVPU7  
HX100PVPU7 SX100PVNU6 SX100PVQU6 UX100PVNU7 UX100PVQU6  
100  
135  
HX135PVNU6 HX135PVQU6 SX135PVNU7 SX135PVQU7 UX135PVPU6 UX135PVQU7  
HX135PVNU7 HX135PVQU7 SX135PVPU7 UX135PVNU6 UX135PVPU7  
HX135PVPU7 SX135PVNU6 SX135PVQU6 UX135PVNU7 UX135PVQU6  
HX165PVNU6 HX165PVQU6 SX165PVNU7 SX165PVQU7 UX165PVPU6 UX165PVQU7  
HX165PVNU7 HX165PVQU7 SX165PVPU7 UX165PVNU6 UX165PVPU7  
HX165PVPU7 SX165PVNU6 SX165PVQU6 UX165PVNU7 UX165PVQU6  
165  
200  
HX200PVNU7 HX200PVQU7 SX200PVPU7 UX200PVNU7 UX200PVQU7  
HX200PVPU7 SX200PVNU7 SX200PVQU7 UX200PVPU7  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
3
 
   
Programming  
Setup of the Machine  
Turn key from Run to Program  
RUN  
PROGRAM  
To go to the main setup of the machine, press  
“Auxiliary”, “2”, “9”.  
Program Cycle 00  
System Program  
_X18PV  
To change the machine type, press the “Advance”  
button.  
The following types are possible:  
System Program  
_X25PV  
_X18PV  
_X25PV  
_X33PV  
_X40PV  
_X55PV  
_X75PV  
_X135PV  
_X165PV  
_X200PV  
Press the “Advance” button until the right type of  
machine is selected. Press the “Enter” button.  
Units: English  
Select the desired units.  
NOTE: English means level in inch and  
temperature in °F.  
Metric means level in cm and temperature in °C.  
Press the “Advance” button to change the units.  
Units: Metric  
Press the “Enter” button.  
Drain 1 : Valve  
Drain 2 : None  
Select the type of drain valve.  
Press “1” to change drain 1 to pump or valve.  
Drain 1 : Pump  
Drain 2 : None  
Press “2” to change drain 2 to pump, valve or none.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
4
   
Programming  
Press the “Enter” button to select options.  
Options :  
Press the “Aux Fill” button for auxiliary fill option or  
press “Enter” for heating.  
Options :  
Aux Fill  
If heating is selected, the user can fill in the kW of the  
electrical heating (example: 9 kW).  
Heating : 6 kW  
Press “0”, “9”.  
Heating : 9 kW  
Press “Enter” to select advance mode in run mode yes  
or no.  
Advance : Yes  
Press “Advance” to change between yes and no.  
Advance : No  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
5
Programming  
Press “Enter” to set the hysteresis level (level at which  
water drops before it senses it must refill).  
Level : hyst 2"  
If English is selected for units, this value will be in  
inches. If Metric is selected for units, this value will be  
in cm.  
Select between 1 to 9 cm or inches.  
Press “Enter” to select the temperature hysteresis  
(level at which temperature drops before machine  
senses it must reheat).  
Temp : hyst 3°F  
Spin retries : 5  
Address : 0  
If English is selected for units, this value will be in °F.  
If Metric is selected for units, this value will be in °C.  
Select 1 to 9 °C or °F.  
Press the “Enter” button to set the spin retries.  
Select 1 to 9 spin retries.  
Press “Enter” to set the network address of the  
machine. If this is not used, press “Enter”.  
The address of the machine has to be set if you  
network the machine. Each machine should have a  
different address.  
Enter to save ?  
Fill in between 00 and 99.  
Press “Enter” to finish the settings.  
Press “Enter” to save the settings or press “Stop” to  
exit without saving.  
Program Cycle 00  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
6
Programming  
NOTE: If chemical hold is off, then supplies 4  
through 9 are controlled exactly like supplies 1  
through 3. A switch closure/opening between pins 1  
and 4 of the COIN header on the output board will  
have no effect.  
Version of Control  
To determine control version, apply power to machine.  
Control will display version of control (i.e., 1.15).  
Language on Display (Version 1.15 and  
later ONLY)  
Program Storing Mode  
To set a different language on the WE-8 display:  
1. Turn key from RUN to PROGRAM.  
The WE-8 control is capable of 99 total cycles. One  
cycle contains 1 or more steps.  
One step is a function of the wash program  
(example: heat).  
2. Press “Auxiliary”, “2” and “9” to enter set-up  
mode.  
Choose between the following functions:  
3. English will display. Press “Advance” until  
desired language displays (French, Italian,  
Spanish and German).  
Fill:  
To fill the machine with water.  
Wash action of the machine.  
Wash:  
Supply:  
4. Press “Enter” keypad.  
To add detergent to the wash (liquid or  
powder).  
5. Press “Enter” to advance through set-up mode.  
6. Wait until information is saved.  
Cooldown: Cool to programmed temperature  
7. Turn key from PROGRAM to RUN.  
8. Display will read language chosen for all cycles.  
Heat:  
Soak:  
To heat the water.  
The wash will be soaked for a  
programmed time and a programmed  
temperature.  
Setup of the Chemical Hold Feature  
(Version 1.11 and later ONLY)  
Aux:  
A relay contact will close for a  
programmed time.  
At power up, verify that model is at least  
version 1.11. Refer to version of Control Section.  
Earlier versions do not have this chemical hold  
feature.  
Spin:  
Drain:  
To spin the machine for a programmed  
time and RPM.  
To drain the water from the machine.  
Insert key into key switch and turn to Program.  
Push the Auxiliary key, the 2 key, and the 9 key  
in succession to enter System Program Mode.  
Push the Start key 10 times to arrive at the  
Chemical hold choice.  
Push the Add Cycle/Advance key to toggle the  
Chemical hold feature either Yes (on) or No (off).  
Push the Start key twice to save changes and exit  
System Program Mode.  
Turn key switch to Run.  
NOTE: If chemical hold is on, then a switch  
closure/opening between pins 1 and 4 of the COIN  
header on the output board will control supplies 4  
through 9. A closure will turn the programmed  
supply/ies on and count down the time for the  
supply to be on. An opening will turn the  
programmed supply/ies off and halt the time for  
the supply to be on.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
7
 
       
Programming  
Example: Warm Low (time limit 5 minutes  
30 seconds)  
Explanation of the Step Functions  
Fill:  
Choose between 4 water inlet configurations and  
3 water levels.  
Step XX Cycle XX  
Warm  
Water Inlet Configurations:  
Cold:  
Hot:  
Only opens the cold water valve.  
Only opens the hot water valve.  
Warm: Opens the cold and hot water valves.  
Aux Fill: Opens an auxiliary water valve  
if installed.  
Step XX Cycle XX  
Warm Low  
Water Levels:  
Low:  
Med:  
High:  
Low water level.  
Medium water level.  
High water level.  
Step XX Cycle XX  
0 min  
The inlet configurations and the fill levels appear on  
the keypad, keys 1, 2, 3 and 8.  
Step XX Cycle XX  
5 min 30 sec  
Be sure to select first the inlet configuration and then  
the water level.  
NOTE: If a fill error occurs, then machine has  
2 minutes to finish filling. If after 2 minutes it has  
not finished filling, cycle is aborted.  
Then you will be asked for the step time limit.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
8
 
Programming  
It is possible to more accurately control the  
Step XX Cycle XX  
95°F Low  
temperature of water coming in to the machine during  
a fill step. This does not apply to “Aux Fill” step. The  
control will mix the hot and cold water inlet to the  
temperature programmed in the fill function. To fill in  
the temperature, select the water inlet type and the  
water level. Press the “Heat” button and the control  
will ask the temperature. In this way the water inlet  
type selected is of no use because the control will mix  
between the cold and hot water inlet to reach the  
temperature.  
Step XX Cycle XX  
0 min  
Example: Fill to low level and 95°F (step time limit:  
5 minutes 30 seconds).  
Step XX Cycle XX  
5 min 30 sec  
Step XX Cycle XX  
Warm  
Step XX Cycle XX  
Warm Low  
Step XX Cycle XX  
0°F  
Step XX Cycle XX  
95°F  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
9
 
Programming  
Wash:  
Supply:  
Choose between 7 different preset wash actions.  
Choose between 9 different supplies.  
Supply 1: Turns on the water valve in compartment  
A of the supply box.  
Action  
Time (sec) (sec)  
Stop Time G-force  
Supply 2: Turns on the water valve in compartment  
B of the supply box.  
Wash 1  
Wash 2  
Wash 3  
Wash 4  
Wash 5*  
Wash 6  
Wash 7  
18  
3
0.5  
0.5  
0
3
0
27  
0
Supply 3: Turns on the water valve in compartment  
C of the supply box.  
10  
18  
4
20  
3
0.5  
0.5  
0.5  
0
Supply 4: Activates supply pump 1.  
Supply 5: Activates supply pump 2.  
Supply 6: Activates supply pump 3.  
Supply 7: Activates supply pump 4.  
Supply 8: Activates supply pump 5.  
Supply 9: Activates supply pump 6.  
The Supply button is button 6.  
56  
0
0
The “Wash” button is button 4 on the display.  
Example: Wash 4 for 8 minutes 00 seconds.  
Example: Supply 1 and 5 for 20 seconds.  
Step XX Cycle XX  
Wash  
Step XX Cycle XX  
Supply  
Step XX Cycle XX  
Wash 4 10/20  
Step XX Cycle XX  
Supply  
1
5
Step XX Cycle XX  
0 min  
Step XX Cycle XX  
0 min  
Step XX Cycle XX  
8 min 00 sec  
Heat:  
Step XX Cycle XX  
0 min 20 sec  
* Refer to section on Wash 5 Thermal Cool-Down.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
10  
 
Programming  
Chemical Hold Feature  
Enter time in minutes  
and press “Enter”  
(example: 5 min).  
Chemical supply injection can be paused. Refer to  
Setup of Chemical Hold Feature.  
Step XX Cycle XX  
1 hours 05 min  
Wash 5 Thermal Cool-Down  
Immediately after a heat step, a temperature-controlled  
thermal cool-down may be programmed to prevent  
fiber shock from sudden cool-down.  
Step XX Cycle XX  
Wash  
The “Heat” button is number 5.  
Example: Heat up to 140°F with the time limit of  
45 minutes.  
Thermal Cool-Down  
is Wash 5.  
Step XX Cycle XX  
Wash 5  
Step XX Cycle XX  
Heat  
Step XX Cycle XX  
0°F (or 0°C)  
Step XX Cycle XX  
0°F  
Enter desired temperature for load to  
cool down to. Three digits must be used  
for temperature. If Fahrenheit, the valid  
temperature range is 80° – 200°F. If  
Celcius, valid temperature range is  
25° – 90°C (example: 95°F).  
Step XX Cycle XX  
140°F  
Step XX Cycle XX  
95°F  
Step XX Cycle XX  
0 hours  
Step XX Cycle XX  
0 hours  
Step XX Cycle XX  
0 hours 45 min  
Step XX Cycle XX  
1 hours 00 min  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
11  
Programming  
Soak:  
Example: Soak time of 2 hours with 32°F.  
Button 7 is the “Soak” button.  
By pressing button 7, “Soak” will appear on the  
display. Press “Enter” to fill in the soak time.  
Step XX Cycle XX  
Soak  
Example: Soak for 2 hours.  
Step XX Cycle XX  
Soak  
Step XX Cycle XX  
0°F  
Use the key pad to fill in  
the soak temperature  
(example: 32°F).  
Step XX Cycle XX  
0 hours  
Step XX Cycle XX  
32°F  
Use the key pad to fill in  
the hours of the soak time  
(example: 2 hours).  
Step XX Cycle XX  
Soak 32°F  
Step XX Cycle XX  
2 hours 00 min  
Now you can fill in the  
minutes (example:  
23 minutes).  
Step XX Cycle XX  
0 hours  
Step XX Cycle XX  
2 hours 23 min  
Use the key pad to fill in  
the hours of the soak time  
(example: 2 hours).  
Press “Enter”.  
Step XX Cycle XX  
2 hours 00 min  
The temperature of the soak will be the temperature  
programmed in the previous step. You can also change  
the temperature by pressing first “Soak” and then  
“Heat”.  
Fill in the minutes  
(example: 23 minutes).  
Step XX Cycle XX  
2 hours 23 min  
Press “Enter”.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
12  
 
Programming  
Spin:  
Drain:  
Choose between 4 preset spin speeds.  
This function drains the water.  
If you have 2 drains, select which drain has to be  
opened.  
18-75  
100/135  
165  
200  
Models Models Models Models  
Spin 1  
RPM  
500  
650  
500  
650  
800  
80  
500  
650  
750  
750  
Step XX Cycle XX  
Drain  
Spin 2  
RPM  
Select Drain 1 or 2.  
If you only have 1 drain,  
you can only select 1.  
Spin 3  
RPM  
800  
Spin 4  
RPM  
1000  
Step XX Cycle XX  
Drain 2  
“Spin” is button 9.  
Step XX Cycle XX  
0 min  
Step XX Cycle XX  
Spin  
Enter the drain time  
(example: 1 minute  
10 seconds).  
Select the spin number  
(example: 3).  
Step XX Cycle XX  
1 min 00 sec  
Step XX Cycle XX  
Spin 3  
Step XX Cycle XX  
0 min  
Step XX Cycle XX  
1 min 10 sec  
Enter the spin time. Enter  
minutes first and then  
seconds (example:  
5 minutes 30 seconds).  
Step XX Cycle XX  
NOTE: With the WE-8 control, it is NOT necessary  
to program a drain step before spin. The spin step  
incorporates the balancing routine and draining  
before beginning high speed spin (as a sub part of  
the spin step). A programmed drain step will be  
skipped if spin step is programmed immediately  
after it.  
5 min 00 sec  
Step XX Cycle XX  
5 min 30 sec  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
13  
Programming  
Example Making a New Program  
Program Cycle 00  
Program 51  
Step 1: Fill warm water to low level  
(5 minutes 30 seconds time limit)  
Step 2: Supply 1 and 5 for 20 seconds  
Program Cycle 51  
Step 3: Heat up to 140°F (45 minutes time limit)  
Step 4: Wash action 4 for 8 minutes 00 seconds  
Step 5: Drain 1 for 1 minutes 25 seconds  
Step 6: Spin 3 for 8 minutes 30 seconds  
To program or edit cycles turn the key into the  
Program Mode.  
Add  
Cycle 51  
“Program Cycle xx” will be shown on the display.  
Step 01  
Cycle 51  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
14  
 
 
Programming  
Step 01 Cycle 51  
Warm  
Step 02 Cycle 51  
Supply  
Step 01 Cycle 51  
Warm Low  
Step 02 Cycle 51  
Supply  
1
5
Step 01 Cycle 51  
0 min  
Step 02 Cycle 51  
0 min  
Step 01 Cycle 51  
5 min 30 sec  
Step 02 Cycle 51  
0 min 20 sec  
End  
Cycle 51  
End  
Cycle 51  
Step 02  
Cycle 51  
Step 03  
Cycle 51  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
15  
 
Programming  
Step 03 Cycle 51  
Heat  
Step 04 Cycle 51  
Wash 4 10/20  
Step 03 Cycle 51  
0°F  
Step 04 Cycle 51  
0 min  
Step 03 Cycle 51  
140°F  
Step 04 Cycle 51  
8 min 00 sec  
Step 03 Cycle 51  
0 hours  
End  
Cycle 51  
Step 03 Cycle 51  
0 hours 45 min  
Step 05 Cycle 51  
End  
Cycle 51  
Step 05 Cycle 51  
Drain 1  
Step 04  
Cycle 51  
Step 05 Cycle 51  
0 min  
Step 04 Cycle 51  
Wash  
Step 05 Cycle 51  
1 min 25 sec  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
16  
 
Programming  
End  
Cycle 51  
Enter to save ?  
Step 06 Cycle 51  
Program Cycle 51  
Step 06 Cycle 51  
Spin 1  
Step 06 Cycle 51  
Spin 3  
Step 06 Cycle 51  
0 min  
Step 06 Cycle 51  
8 min 30 sec  
End  
Cycle 51  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
17  
 
Programming  
Edit a Cycle  
Program Cycle 00  
Change a Complete Step  
To edit a cycle enter the cycle number  
(example: cycle 51).  
Program Cycle 51  
Edit  
Cycle 51  
Press the “Edit Cycle” button.  
Name Cycle 51:  
Cycle 51  
Press the “Enter” button to edit the cycle.  
Step 01 Cycle 51  
Warm Low  
Press “Enter” to continue.  
The first step of cycle 51 will display.  
Step 02 Cycle 51  
Wash 1 18/3  
Select the step being edited by using the “Advance”  
button to go to the next step or the “Previous” button  
to go to the previous step.  
If you would like to change the step, press the “Clear”  
button.  
Step 02 Cycle 51  
Wash  
Select another wash action or press the “Clear” button  
to change the function.  
Step 02 Cycle 51  
Fill in the function desired (example: soak for 1 hour  
30 minutes).  
Press the “Soak” button.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
18  
   
Programming  
Step 02 Cycle 51  
Soak  
Step 02 Cycle 51  
0 hours  
Step 02 Cycle 51  
1 hours 00 min  
Step 02 Cycle 51  
1 hours 30 min  
Step 03 Cycle 51  
XXXXXXXX  
The control is then in the next step of cycle 51. Press  
“Advance” until the display shows “End Cycle 55”.  
End  
Cycle  
Press “Enter” to confirm.  
Enter to save ?  
Press “Enter” to save or “Stop” to ignore the changes.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
19  
Programming  
Changing the Time of a Step  
Program Cycle 00  
To edit a cycle, enter the cycle number  
(example: cycle 51).  
Program Cycle 51  
Press the “Edit Cycle” button.  
Edit  
Cycle 51  
Press the “Enter” button to edit the cycle.  
Name Cycle 51:  
Cycle 51  
Press “Enter” to continue.  
The first step of cycle 51 will display.  
Step 01 Cycle 51  
Warm Low  
Select the step being edited by using the “Advance”  
button to go to the next step or the “Previous” button  
to go to the previous step.  
Step 02 Cycle 51  
Wash 1 18/3  
Press “Enter” to change the time of the wash action.  
Step 02 Cycle 51  
5 min 00 sec  
Press “Clear” to change the time.  
Step 01 Cycle 51  
5 min  
Fill in another time (example: 6 minutes 20 seconds).  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
20  
 
Programming  
Step 02 Cycle 51  
6 min 00 sec  
Step 02 Cycle 51  
6 min 20 sec  
Press “Enter” to go to the next step.  
Step 03 Cycle 51  
XXXXXXX  
Press the “Advance” button until display shows “End  
Cycle 51”.  
End  
Cycle 51  
Press “Enter” to confirm.  
Enter to save ?  
Press “Enter” to save or “Stop” to ignore the changes.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
21  
Programming  
Delete a Step  
Program Cycle 00  
To edit a cycle, enter the cycle number  
(example: cycle 51).  
Program Cycle 51  
Press the “Edit Cycle” button.  
Edit  
Cycle 51  
Press the “Enter” button to edit the cycle.  
Name Cycle 51:  
Cycle 51  
Press “Enter” to continue.  
The first step of cycle 51 will display.  
Step 01 Cycle 51  
Warm Low  
Select the step being edited by using the “Advance”  
button to go to the next step or the “Previous” button  
to go to the previous step.  
Step 02 Cycle 51  
Wash 1 18/3  
Press the “Clear” button to change the step.  
Press the “Clear” button again.  
Step 02 Cycle 51  
Wash  
Step 02 Cycle 51  
Press the “Clear” button once more.  
Step deleted  
The step is deleted. Press the “Advance” button to end  
cycle 51 and press “Enter” 2 times to save the settings.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
22  
 
Programming  
Insert a Step  
Program Cycle 00  
To edit a cycle, enter the cycle number  
(example: cycle 51).  
Program Cycle 51  
Press the “Edit Cycle” button.  
Edit  
Cycle 51  
Press the “Enter” button to edit the cycle.  
Name Cycle 51:  
Cycle 51  
Press “Enter” to continue.  
The first step of cycle 51 will display.  
Step 01 Cycle 51  
Warm Low  
Select the position where you would like to add a step  
by using the “Advance” button to go to the next step or  
the “Previous” button to go to the previous step.  
Step 02 Cycle 51  
Wash 1 18/3  
Push the “Add Step” button to add a step.  
The control will insert a step before the step selected.  
Select the function (example: supply).  
Step 02 Cycle 51  
Step 02 Cycle 51  
Supply  
Press the supply number (example: supply 7).  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
23  
 
Programming  
Step 02 Cycle 51  
Supply  
7
Press “Enter” to confirm.  
Step 02 Cycle 51  
0 min  
Enter the time to activate the supply  
(example: 0 minutes 23 seconds).  
Step 02 Cycle 51  
0 min 00 sec  
Step 02 Cycle 51  
0 min 23 sec  
Press “Enter” to confirm.  
Step 03 Cycle 51  
Wash 1 18/3  
Press the “Advance” button until  
“End Cycle 51” is displayed.  
End Cycle 51  
Press “Enter” to confirm.  
Enter to save ?  
Press “Enter” to save or “Stop” to ignore the changes.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
24  
Programming  
Delete a Cycle  
Program Cycle 00  
Press the “Erase Cycle” button.  
Erase Cycle 00  
Erase Cycle 55  
Enter to save ?  
Press the number of the cycle being erased  
(example: 55).  
Press “Enter” to confirm.  
Press “Enter” to save or “Stop” to ignore the changes.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
25  
 
Programming  
Reloading Previous Settings  
This special function allows previous settings to be  
restored.  
Program Cycle 00  
Press “Auxiliary”, “3”, “0”.  
Enter to reload  
earlier settings  
The control will ask if earlier settings are desired.  
Press “Enter” to confirm the settings.  
NOTE: This function only goes back to the last  
programming function entered.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
26  
 
Programming  
Cycle Count  
Reading Cycle Count  
Program Cycle xx  
1. Enter Program Mode by turning key to  
PROGRAM position (xx represents a cycle  
number from 00 to 99).  
PROGRAM  
RUN  
Program Cycle xx  
2. Press “Auxiliary” key, then “3” key, then “1” key.  
Total Working  
Hours 347  
3. The total hours of cycle operation (actual run  
time) will display. Press “Advance” key to  
continue.  
Example display shows 347 total hours (of all  
cycles).  
4. Display now shows total cycle count. Press  
“Advance” key to continue into calibration  
mode, or press “Clear/Stop” key to exit.  
Total Cycle : 5  
Example display shows 5 total cycles have been  
run.  
OR...  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
27  
   
Programming  
Calibration of the Machine  
The _x__PV should reflect the size selected in earlier  
steps.  
Turn key to Program Mode.  
Program Cycle 00  
Press “Auxiliary”, “3”, “1”.  
Total working  
hours : 0  
The total hours the machine was running will be  
displayed.  
Press “Advance” and screen will show total cycles.  
Press “Advance” to calibrate the water level sensor.  
level : 0.0 “  
Enter to zero  
If the value is not zero, press “Enter” and the value  
will change to zero.  
Press “Advance” to calibrate the motor.  
Spin  
XXX rpm  
The board will lock the door and let the motor spin at  
approximately 500 rpm (Firmware version 1.12 or  
higher). The rpm will increase on the display. If the  
machine reached approximately 500 rpm, the display  
will show a reference value.  
Reference x.xx  
After the reference value is shown, the machine will  
coast down to stop. When the machine stands still, the  
board will unlock the door.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
28  
 
Programming  
Speed Calibration  
Calibrate 2  
500 rpm  
This function automatically calibrates water level,  
distribution speed and spin speed.  
Ref: #  
Offset: #  
Total working  
hours : #  
Coast down  
Please wait  
Program Cycle #  
Total Cycle:  
#
End of Calibration  
Calibration  
and testing  
level: 0.0"  
Enter to zero  
If shell is empty of  
water and display reads  
0.0", then press “Add  
Cycle/Advance”.  
Motor Control  
Distribute Speed  
# rpm  
Spin  
# rpm  
Calibrate 1  
100 rpm  
Spin  
# rpm  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
 
9001889  
29  
 
Pre-Programmed Cycles  
Cycle 01  
Sheets Light Soil  
Cycle 02  
Sheets No Bleach  
Step  
1
Description  
Min:sec  
5:00  
0:45  
7:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
Min:sec  
5:00  
0:45  
7:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Hot Fill to Low Level  
Hot Fill to Low Level  
2
Supply 1, 2, 4, 5  
Wash 1 18/3 (32°F)  
Drain 1  
2
Supply 1, 4  
3
3
Wash 1 18/3 (32°F)  
Drain 1  
4
4
5
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
5
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
6
6
7
7
8
Spin 1  
8
Spin 1  
9
100°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
9
100°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
10  
11  
12  
13  
Spin 1  
Spin 1  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
30  
 
 
Pre-Programmed Cycles  
Cycle 03  
Towels Light Soil  
Cycle 04  
Towels No Bleach  
Step  
1
Description  
Min:sec  
5:00  
0:45  
7:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
5:00  
1:00  
6:00  
Step  
1
Description  
Min:sec  
5:00  
0:45  
7:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
6:00  
Hot Fill to Low Level  
Hot Fill to Low Level  
2
Supply 1, 2, 4, 5  
Wash 1 18/3 (32°F)  
Drain 1  
2
Supply 1, 4  
3
3
Wash 1 18/3 (32°F)  
Drain 1  
4
4
5
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
5
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
6
6
7
7
8
Spin 1  
8
Spin 1  
9
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
9
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
10  
11  
12  
13  
Spin 4  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
31  
 
Pre-Programmed Cycles  
Cycle 05  
Sheets Medium Soil  
Cycle 06  
Towels Medium Soil  
Step  
1
Description  
Min:sec  
5:00  
0:45  
6:00  
1:00  
5:00  
0:45  
6:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
Min:sec  
5:00  
Hot Fill to Low Level  
Hot Fill to Low Level  
2
Supply 1, 4  
2
Supply 1, 4  
0:45  
6:00  
1:00  
5:00  
0:45  
6:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
6:00  
3
Wash 1 18/3 (32°F)  
Drain 1  
3
Wash 1 18/3 (32°F)  
Drain 1  
4
4
5
Hot Fill to Low Level  
Supply 2, 5  
5
Hot Fill to Low Level  
Supply 2, 5  
6
6
7
Wash 1 18/3 (32°F)  
Drain 1  
7
Wash 1 18/3 (32°F)  
Drain 1  
8
8
9
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
9
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
10  
11  
12  
13  
14  
15  
16  
17  
Spin 1  
Spin 1  
100°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
32  
 
Pre-Programmed Cycles  
Cycle 07  
Blankets Warm  
Cycle 08  
Spreads Cold  
Step  
1
Description  
Warm Fill to High Level  
Supply 1, 4  
Min:sec  
5:00  
0:45  
6:00  
1:00  
5:00  
5:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
4:00  
Step  
1
Description  
Min:sec  
5:00  
0:45  
6:00  
1:00  
5:00  
1:30  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
4:00  
Cold Fill to High Level  
Supply 1, 4  
2
2
3
Wash 1 18/3 (32°F)  
Drain 1  
3
Wash 2 3/27 (32°F)  
Drain 1  
4
4
5
Warm Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
5
Cold Fill to High Level  
Wash 2 3/27 (32°F)  
Drain 1  
6
6
7
7
8
Spin 1  
8
Spin 1  
9
Warm Fill to Low Level  
Supply 3, 6, 7  
9
Cold Fill to High Level  
Supply 3, 6, 7  
Wash 2 3/27 (32°F)  
Drain 1  
10  
11  
12  
13  
10  
11  
12  
13  
Wash 2 3/27 (32°F)  
Drain 1  
Spin 4  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
33  
 
Pre-Programmed Cycles  
Cycle 09  
Towels Heavy Soil  
Cycle 10  
Rinse and Spin  
Step  
1
Description  
Min:sec  
5:00  
0:45  
7:00  
5:00  
1:00  
7:00  
1:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
1:00  
4:00  
1:00  
6:00  
Step  
Description  
Warm Fill to Low Level  
Wash 1 18/3 (32°F)  
Drain 1  
Min:sec  
5:00  
Hot Fill to Low Level  
1
2
3
4
5
2
Supply 1, 4  
1:00  
3
Wash 1 18/3 (32°F)  
Hot Fill to High Level  
Supply 2, 5  
1:00  
4
Spin 1  
1:00  
5
Spin 4  
4:00  
6
Wash 1 18/3 (32°F)  
Drain 1  
7
8
Spin 1  
9
Warm Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
Spin 1  
Warm Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
34  
 
Pre-Programmed Cycles  
Cycle 11  
Health Care Sheets Light Soil  
Cycle 12  
Health Care Towels Light Soil  
Step  
1
Description  
Warm Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1, 2, 4, 5  
Hot Fill to Low Level  
Supply 1, 2  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
8:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
4:00  
Step  
1
Description  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
8:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
4:00  
Warm Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
2
2
3
3
4
4
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Wash 1 18/3 (32°F)  
Drain 1  
5
5
6
Wash 1 18/3 (32°F)  
Drain 1  
6
7
7
8
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
8
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
9
9
10  
11  
12  
13  
14  
15  
16  
10  
11  
12  
13  
14  
15  
16  
Spin 1  
Spin 1  
100°F Fill to Low Level  
Supply 3, 6, 7  
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
35  
 
Pre-Programmed Cycles  
Cycle 13  
Health Care Sheets Heavy Soil  
Cycle 14  
Health Care Towels Heavy Soil  
Step  
1
Description  
Min:sec  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
32°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Min:sec  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
6:00  
32°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
2
2
3
3
4
120°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1, 4  
4
120°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
5
5
6
6
7
Hot Fill to Low Level  
Supply 1  
7
Hot Fill to Low Level  
Supply 1, 4  
8
8
9
Wash 1 18/3 (32°F)  
Drain 1  
9
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
Hot Fill to Low Level  
Supply 2, 5  
Hot Fill to Low Level  
Supply 2, 5  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
100°F Fill to Low Level  
Supply 3, 6, 7  
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
36  
 
Pre-Programmed Cycles  
Cycle 15  
Health Care Cotton Blankets  
Cycle 16  
Health Care Diapers Heavy Soil  
Step  
1
Description  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
6:00  
Step  
1
Description  
32°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Min:sec  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:30  
7:00  
1:00  
5:00  
0:30  
7:00  
1:00  
5:00  
4:00  
1:00  
2:00  
5:00  
2:00  
1:00  
5:00  
0:30  
4:00  
1:00  
1:00  
6:00  
2
2
3
3
4
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Wash 1 18/3 (32°F)  
Drain 1  
4
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
5
5
6
6
7
7
Hot Fill to Low Level  
Supply 1, 4  
8
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
8
9
9
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
Spin 1  
Hot Fill to Low Level  
Supply 1, 4  
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to Low Level  
Supply 2, 5  
Spin 4  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
37  
 
Pre-Programmed Cycles  
Cycle 17  
Health Care Personal Bleach  
Cycle 18  
Health Care Personal No Bleach  
Step  
1
Description  
Min:sec  
5:00  
0:45  
6:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
Hot Fill to Low Level  
Supply 1, 4  
Min:sec  
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Wash 1 18/3 (32°F)  
Drain 1  
5:00  
0:45  
6:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
2
2
3
3
Wash 1 18/3 (32°F)  
Drain 1  
4
4
5
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
5
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
6
6
7
7
8
Spin 1  
8
Spin 1  
9
110°F Fill to Low Level  
Supply 3, 6, 7  
9
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
10  
11  
12  
13  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
38  
 
Pre-Programmed Cycles  
Cycle 19  
Health Care Pads Polyester  
Cycle 20  
Table Linen Iron  
Step  
1
Description  
110°F Fill to Low Level  
Supply 1, 4  
Min:sec  
5:00  
0:45  
3:00  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
3:00  
1:00  
4:00  
Step  
1
Description  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
2:00  
0:30  
5:00  
1:00  
4:00  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
2
2
3
Wash 1 18/3 (32°F)  
130°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
3
4
4
Hot Fill to Low Level  
Supply 1, 4  
5
5
6
6
Wash 1 18/3 (32°F)  
Drain 1  
7
Hot Fill to Low Level  
Supply 1, 4  
7
8
8
Hot Fill to Low Level  
Supply 2, 5  
9
Wash 1 18/3 (32°F)  
Drain 1  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to Low Level  
Supply 2, 5  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to Low Level  
Supply 3, 6  
Wash 1 18/3 (32°F)  
Supply 6, 8  
Spin 1  
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 2  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
39  
 
Pre-Programmed Cycles  
Cycle 21  
Table Linen No Iron  
Cycle 22  
Table Color Iron  
Step  
1
Description  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
4:00  
0:30  
5:00  
1:00  
4:00  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
2
2
3
3
4
Hot Fill to Low Level  
Supply 1, 4  
4
Hot Fill to Low Level  
Supply 1, 4  
5
5
6
Wash 1 18/3 (32°F)  
Drain 1  
6
Wash 1 18/3 (32°F)  
Drain 1  
7
7
8
Hot Fill to Low Level  
Supply 2, 5  
8
Hot Fill to Low Level  
Supply 1, 4  
9
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
110°F Fill to Low Level  
Supply 3, 6, 7  
110°F Fill to Low Level  
Supply 3, 6  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Supply 8  
Spin 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 2  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
40  
 
Pre-Programmed Cycles  
Cycle 23  
Table Color No Iron  
Cycle 24  
Visa Iron  
Step  
1
Description  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
4:00  
Step  
1
Description  
Min:sec  
5:00  
3:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:30  
2:00  
0:30  
5:00  
1:00  
3:00  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
2
2
3
3
4
Hot Fill to Low Level  
Supply 1, 4  
4
Hot Fill to Low Level  
Supply 1, 4  
5
5
6
Wash 1 18/3 (32°F)  
Drain 1  
6
Wash 1 18/3 (32°F)  
Drain 1  
7
7
8
Hot Fill to Low Level  
Supply 1, 4  
8
Hot Fill to Low Level  
Supply 2, 5  
9
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to Low Level  
Supply 3, 6  
Spin 1  
Wash 1 18/3 (32°F)  
Supply 8  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 2  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
41  
 
Pre-Programmed Cycles  
Cycle 25  
Visa No Iron  
Cycle 26  
Visa Color Iron  
Step  
1
Description  
Min:sec  
5:00  
3:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1, 4  
Min:sec  
5:00  
3:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:30  
2:00  
0:30  
4:00  
1:00  
3:00  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
2
2
3
3
4
Hot Fill to Low Level  
Supply 1, 4  
4
Hot Fill to Low Level  
Supply 1  
5
5
6
Wash 1 18/3 (32°F)  
Drain 1  
6
Wash 1 18/3 (32°F)  
Drain 1  
7
7
8
Hot Fill to Low Level  
Supply 2, 5  
8
Hot Fill to Low Level  
Supply 1, 4  
9
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to Low Level  
Supply 3, 6  
110°F Fill to Low Level  
Supply 3, 6  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Supply 8  
Spin 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 2  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
42  
 
Pre-Programmed Cycles  
Cycle 27  
Visa Color No Iron  
Cycle 28  
Shirt Color Starch  
Step  
1
Description  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Min:sec  
5:00  
3:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
Min:sec  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
5:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
0:30  
4:00  
1:00  
3:00  
Hot Fill to Low Level  
2
2
Supply 1, 4  
3
3
Wash 1 18/3 (32°F)  
Drain 1  
4
Hot Fill to Low Level  
Supply 1, 4  
4
5
5
Hot Fill to Low Level  
Supply 1, 4  
6
Wash 1 18/3 (32°F)  
Drain 1  
6
7
7
Wash 1 18/3 (32°F)  
Drain 1  
8
Hot Fill to Low Level  
Supply 1, 4  
8
9
9
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Cold Fill to High Level  
Supply 3, 6  
Spin 1  
Supply 5  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 2  
110°F Fill to Low Level  
Supply 3, 6  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
43  
 
Pre-Programmed Cycles  
Cycle 29  
Shirt Bleach Starch  
Cycle 30  
Shirt Color No Bleach  
Step  
1
Description  
Min:sec  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
Min:sec  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
5:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
0:30  
0:30  
4:00  
1:00  
3:00  
Hot Fill to Low Level  
Hot Fill to Low Level  
2
Supply 1, 4  
2
Supply 1, 4  
3
Wash 1 18/3 (32°F)  
Drain 1  
3
Wash 1 18/3 (32°F)  
Drain 1  
4
4
5
Hot Fill to Low Level  
Supply 2, 5  
5
Hot Fill to Low Level  
Supply 1, 4  
6
6
7
Wash 1 18/3 (32°F)  
Drain 1  
7
Wash 1 18/3 (32°F)  
Drain 1  
8
8
9
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
9
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
10  
11  
12  
13  
14  
15  
16  
17  
18  
Spin 1  
Spin 1  
Cold Fill to High Level  
Supply 3, 6  
Cold Fill to High Level  
Supply 3, 6  
Supply 2, 8  
Supply 4  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 2  
Spin 2  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
44  
 
Pre-Programmed Cycles  
Cycle 31  
Shirt Delicate  
Cycle 32  
Starch Extract  
Step  
1
Description  
Warm Fill to Low Level  
Wash 2 3/27 (32°F)  
Drain 1  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
5:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:30  
0:30  
3:00  
1:00  
1:30  
Step  
Description  
Min:sec  
5:00  
1
2
3
4
5
Warm Fill to Low Level  
Supply 2, 8  
2
0:30  
3
Wash 1 18/3 (32°F)  
Drain 1  
7:00  
4
Warm Fill to Low Level  
Supply 1, 4  
1:00  
5
Spin 2  
3:00  
6
Wash 2 3/27 (32°F)  
Drain 1  
7
8
Warm Fill to High Level  
Wash 2 3/27 (32°F)  
Drain 1  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
Warm Fill to High Level  
Wash 2 3/27 (32°F)  
Drain 1  
Cold Fill to High Level  
Supply 3, 6, 7  
Supply 4  
Wash 2 3/27 (32°F)  
Drain 1  
Spin 2  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
45  
 
Pre-Programmed Cycles  
Cycle 33  
Uniforms Bleach  
Cycle 34  
Uniforms No Bleach  
Step  
1
Description  
Min:sec  
5:00  
3:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
3:00  
1:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
Step  
1
Description  
Min:sec  
5:00  
0:45  
6:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
3:00  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to Low Level  
2
2
Supply 1, 4  
3
3
Wash 1 18/3 (32°F)  
Drain 1  
4
Hot Fill to Low Level  
Supply 1, 4  
4
5
5
110°F Fill to Low Level  
Wash 1 18/3 (32°F)  
Drain 1  
6
Wash 1 18/3 (32°F)  
Drain 1  
6
7
7
8
Hot Fill to Low Level  
Supply 2, 5  
8
Spin 1  
9
9
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to Low Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
46  
 
Pre-Programmed Cycles  
Cycle 35  
Rags Heavy Soil  
Cycle 36  
Mops in Bags  
Step  
1
Description  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
6:00  
Step  
1
Description  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
4:00  
1:00  
4:00  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
2
2
3
3
4
Hot Fill to Low Level  
Supply 1, 4  
4
Hot Fill to Low Level  
Supply 1, 4  
5
5
6
Wash 1 18/3 (32°F)  
Drain 1  
6
Wash 1 18/3 (32°F)  
Drain 1  
7
7
8
Hot Fill to Low Level  
Supply 2, 5  
8
Hot Fill to Low Level  
Supply 2, 5  
9
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
110°F Fill to Low Level  
Supply 3, 6  
110°F Fill to Low Level  
Supply 3, 6  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 4  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
47  
 
Pre-Programmed Cycles  
Cycle 37  
Rewash/Reclaim  
Cycle 38  
Supply Setup  
Step  
1
Description  
Min:sec  
5:00  
2:00  
1:00  
5:00  
0:45  
4:00  
1:00  
5:00  
0:45  
7:00  
1:00  
5:00  
4:00  
1:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:30  
4:00  
0:30  
4:00  
1:00  
4:00  
Step  
1
Description  
Warm Fill to Low Level  
Supply 1  
Min:sec  
5:00  
2:00  
2:00  
2:00  
2:00  
2:00  
1:00  
5:00  
2:00  
2:00  
2:00  
2:00  
0:30  
1:00  
130°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
2
2
3
3
Supply 2  
4
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Wash 1 18/3 (32°F)  
Drain 1  
4
Supply 3  
5
5
Supply 4  
6
6
Supply 5  
7
7
Drain 1  
8
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Wash 1 18/3 (32°F)  
Drain 1  
8
Warm Fill to Low Level  
Supply 6  
9
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
10  
11  
12  
13  
14  
Supply 7  
Supply 8  
Hot Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Supply 9  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
110°F Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
110°F Fill to High Level  
Supply 3, 6  
Wash 1 18/3 (32°F)  
Supply 3, 6  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
48  
 
Pre-Programmed Cycles  
Cycle 39  
Test Program  
Cycle 39  
Test Program  
Step  
1
Description  
Cold Fill to High Level  
Drain 1  
Min:sec  
0:30  
0:10  
5:00  
5:00  
1h00  
5:00  
0:30  
0:30  
0:30  
0:30  
0:30  
1:00  
0:30  
0:30  
0:30  
0:30  
0:30  
0:30  
0:30  
0:30  
0:30  
1:00  
0:05  
0:05  
0:05  
5:00  
5:00  
2h00  
1:00  
2:00  
2:00  
2:00  
2:00  
0:15  
5:00  
Step  
36  
Description  
Min:sec  
0:15  
Wash 1 18/3 (32°F)  
Drain 1  
2
37  
1:00  
3
Hot Fill to Low Level  
Auxiliary Fill to Med Level  
Heat (150°F)  
Cold Fill to High Level  
Supply 1  
4
5
6
7
8
Supply 2  
9
Supply 3  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
Supply 4  
Supply 5  
Drain 1  
Warm Fill to Low Level  
Supply 6  
Supply 7  
Supply 8  
Supply 9  
Wash 2 3/27 (32°F)  
Wash 3, no agitation (32°F)  
Wash 4 10/3 (32°F)  
Wash 1, no reverse (32°F)  
Drain 1  
Auxiliary 1  
Auxiliary 2  
Auxiliary 3  
150°F Fill to High Level  
Cold Fill to Overflow  
Soak (150°F)  
Drain 1  
Spin 1  
Spin 2  
Spin 3  
Spin 4  
Auxiliary 3  
Cold Fill to Med Level  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
49  
 
Pre-Programmed Cycles  
Cycle 40  
Energy Hot  
Cycle 41  
Energy Warm  
Step  
1
Description  
Min:sec  
5:00  
0:15  
4:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:15  
2:00  
3:00  
Step  
1
Description  
Warm Fill to Low Level  
Supply 1, 2  
Min:sec  
5:00  
0:15  
4:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:15  
2:00  
3:00  
Hot Fill to Low Level  
Supply 1, 2  
2
2
3
Wash 1 18/3 (32°F)  
Drain 1  
3
Wash 1 18/3 (32°F)  
Drain 1  
4
4
5
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
5
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
6
6
7
7
8
Cold Fill to High Level  
Supply 3  
8
Cold Fill to High Level  
Supply 3  
9
9
10  
11  
Wash 1 18/3 (32°F)  
Spin 4  
10  
11  
Wash 1 18/3 (32°F)  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
50  
 
Pre-Programmed Cycles  
Cycle 42  
Energy Cold  
Cycle 50  
Normal 95°C  
Step  
1
Description  
Cold Fill to Low Level  
Supply 1, 2  
Min:sec  
5:00  
0:15  
4:00  
1:00  
5:00  
2:00  
1:00  
5:00  
0:15  
2:00  
3:00  
Step  
1
Description  
Min:sec  
5:00  
0:30  
1h00  
2:00  
1:00  
5:00  
0:30  
1h00  
6:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
3:00  
1:00  
5:00  
Warm Fill to Low Level  
Supply 1, 4  
2
2
3
Wash 1 18/3 (32°F)  
Drain 1  
3
Heat (104°F)  
4
4
Wash 1 18/3 (32°F)  
Drain 1  
5
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
5
6
6
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Heat (203°F)  
7
7
8
Cold Fill to High Level  
Supply 3  
8
9
9
Wash 1 18/3 (32°F)  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
Wash 1 18/3 (32°F)  
Spin 4  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Cold Fill to High Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
51  
 
Pre-Programmed Cycles  
Cycle 51  
Normal 60°C  
Cycle 52  
Normal 40°C  
Step  
1
Description  
Min:sec  
5:00  
0:30  
1h00  
2:00  
1:00  
5:00  
0:30  
1h00  
6:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
3:00  
1:00  
5:00  
Step  
1
Description  
Warm Fill to Low Level  
Supply 1, 4  
Min:sec  
5:00  
0:30  
1h00  
2:00  
1:00  
5:00  
0:30  
1h00  
6:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
3:00  
1:00  
5:00  
Warm Fill to Low Level  
Supply 1, 4  
2
2
3
Heat (104°F)  
3
Heat (104°F)  
4
Wash 1 18/3 (32°F)  
Drain 1  
4
Wash 1 18/3 (32°F)  
Drain 1  
5
5
6
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Heat (140°F)  
6
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Heat (104°F)  
7
7
8
8
9
Wash 1 18/3 (32°F)  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
9
Wash 1 18/3 (32°F)  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
Cold Fill to High Level  
Supply 3, 6, 7  
Cold Fill to High Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 4  
Spin 4  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
52  
 
Pre-Programmed Cycles  
Cycle 53  
Gentle Cold  
Cycle 54  
Perm Press 95°C  
Step  
1
Description  
Cold Fill to High Level  
Supply 1, 4  
Min:sec  
5:00  
0:30  
2:00  
1:00  
5:00  
2:00  
1:00  
1:00  
0:30  
0:30  
3:00  
1:00  
2:00  
Step  
1
Description  
Min:sec  
5:00  
0:30  
1h00  
2:00  
1:00  
5:00  
0:30  
1h00  
6:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
3:00  
1:00  
3:00  
Warm Fill to Low Level  
Supply 1, 4  
2
2
3
Wash 2 3/27 (32°F)  
Drain 1  
3
Heat (104°F)  
4
4
Wash 1 18/3 (32°F)  
Drain 1  
5
Cold Fill to High Level  
Wash 2 3/27 (32°F)  
Drain 1  
5
6
6
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Heat (203°F)  
7
7
8
Spin 1  
8
9
Cold Fill to High Level  
Supply 3, 6, 7  
Wash 2 3/27 (32°F)  
Drain 1  
9
Wash 1 18/3 (32°F)  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
Spin 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Cold Fill to High Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
53  
 
Pre-Programmed Cycles  
Cycle 55  
Perm Press 60°C  
Cycle 56  
Perm Press 40°C  
Step  
1
Description  
Min:sec  
5:00  
0:30  
1h00  
2:00  
1:00  
5:00  
0:30  
1h00  
6:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
3:00  
1:00  
3:00  
Step  
1
Description  
Warm Fill to Low Level  
Supply 1, 4  
Min:sec  
5:00  
0:30  
1h00  
2:00  
1:00  
5:00  
0:30  
1h00  
6:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
5:00  
2:00  
1:00  
1:00  
5:00  
0:30  
3:00  
1:00  
3:00  
Warm Fill to Low Level  
Supply 1, 4  
2
2
3
Heat (104°F)  
3
Heat (104°F)  
4
Wash 1 18/3 (32°F)  
Drain 1  
4
Wash 1 18/3 (32°F)  
Drain 1  
5
5
6
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Heat (140°F)  
6
Hot Fill to Low Level  
Supply 1, 2, 4, 5  
Heat (140°F)  
7
7
8
8
9
Wash 1 18/3 (32°F)  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
9
Wash 1 18/3 (32°F)  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Cold Fill to High Level  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
Cold Fill to High Level  
Supply 3, 6, 7  
Cold Fill to High Level  
Supply 3, 6, 7  
Wash 1 18/3 (32°F)  
Drain 1  
Wash 1 18/3 (32°F)  
Drain 1  
Spin 1  
Spin 1  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
54  
 
Pre-Programmed Cycles  
Cycle 57  
Gentle 30°C  
Step  
1
Description  
Cold Fill to High Level  
Supply 1, 4  
Min:sec  
5:00  
0:30  
2:00  
1:00  
5:00  
0:30  
1h00  
3:00  
1:00  
5:00  
2:00  
1:00  
1:00  
1:00  
5:00  
0:30  
3:00  
1:00  
2:00  
2
3
Wash 2 3/27 (32°F)  
Drain 1  
4
5
Cold Fill to High Level  
Supply 1, 2, 4, 5  
Heat (86°F)  
6
7
8
Wash 2 3/27 (32°F)  
Drain 1  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
Cold Fill to High Level  
Wash 2 3/27 (32°F)  
Drain 1  
Spin 1  
Drain 1  
Cold Fill to High Level  
Supply 3, 6, 7  
Wash 2 3/27 (32°F)  
Drain 1  
Spin 1  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
55  
 
Inverter Drive Error Codes  
Operation  
Panel  
Indication  
Name  
Description and NOTES  
Check point  
Corrective action  
Overcurrent  
When the inverter output current reaches  
Check the motor Repair the wiring.  
shut-off during or exceeds approximately 200% of the  
cable insulation and  
connection for output  
acceleration  
rated current during acceleration, the  
protective circuit is activated to stop the short-circuit/ground  
inverter output.  
fault.  
Overcurrent  
When the inverter output current reaches  
Check the motor Repair the wiring.  
shut-off during or exceeds approximately 200% of the  
constant speed rated current during constant speed, the  
cable insulation and  
connection for output  
protective circuit is activated to stop the short-circuit/ground  
inverter output.  
fault.  
Overcurrent  
When the inverter output current reaches  
Check for sudden  
ContactAlliance  
speed reduction.  
Check the motor  
cable insulation and  
connection for  
output short-circuit/  
ground fault.  
Laundry Systems’  
Customer Service  
department.  
shut-off during or exceeds approximately 200% of the  
deceleration  
rated current during deceleration (other  
than acceleration or constant speed), the  
protective circuit is activated to stop the  
inverter output.  
Repair the wiring.  
Regenerative  
overvoltage  
If regenerative energy causes the  
inverter’s internal main circuit DC voltage the machine is loaded properly to distribute  
Check to make sure  
Load the machine  
shut-off during to reach or exceed the specified value, the properly and that the the load evenly.  
acceleration  
protective circuit is activated to stop the  
inverter output. It may also be activated  
by a surge voltage generated in the power  
supply system.  
load is balanced.  
Regenerative  
overvoltage  
If regenerative energy causes the  
inverter’s internal main circuit DC voltage the machine is loaded properly to distribute  
Check to make sure  
Load the machine  
shut-off during to reach or exceed the specified value, the properly and that the the load evenly.  
constant speed protective circuit is activated to stop the  
inverter output. It may also be activated  
by a surge voltage generated in the power  
supply system.  
load is balanced.  
Regenerative  
overvoltage  
If regenerative energy causes the  
inverter’s internal main circuit DC voltage the machine is loaded properly to distribute  
Check to make sure  
Load the machine  
shut-off during to reach or exceed the specifed value, the properly and that the the load evenly.  
deceleration or protective circuit is activated to stop the  
load is balanced.  
stop  
inverter output. It may also be activated  
by a surge voltage generated in the power  
supply system.  
Motor overload The electronic overcurrent protection in  
Verify that the AC  
Contact Alliance  
shut-off  
the inverter detects motor overheat due to drive’s parameters are Laundry Systems’  
(electronic  
overcurrent  
protection)  
overload or reduced cooling capability  
due to overload or reduced cooling  
capability during constant-speed operation  
to stop the inverter output. When a multi-  
pole motor or two or more motors are run,  
provide a thermal relay in the output side  
of the inverter.  
correct.  
Customer Service  
department.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
56  
 
 
Inverter Drive Error Codes  
Operation  
Panel  
Indication  
Name  
Inverter  
Description and NOTES  
Check point  
Corrective action  
If a current of more than 150% of the rated Verify that the AC  
Contact Alliance  
overload shut-  
off (electronic  
overcurrent  
output current flows and overcurrent shut- drive’s parameters are Laundry Systems’  
off does not occur (200% or less) inverse- correct.  
time characteristics cause the electronic  
overcurrent protection to be activated to  
stop the inverter output in order to protect  
the output transistors.  
Customer Service  
department.  
protection)  
Note: Resetting the inverter initializes  
the internal heat integrating data of the  
electronic overcurrent protection.  
Fin overheat  
If the cooling fin overheats, the overheat  
sensor is actuated to stop the inverter  
output.  
Check for too  
Verify that the AC  
drive’s parameters are  
correct.  
high ambient  
temperature.  
Check for  
Contact Alliance  
Laundry Systems’  
Customer Service  
department.  
cooling fin clogging  
Brake transistor Internal Circuit Error  
alarm detection  
Contact Alliance  
Laundry Systems’  
Customer Service  
department.  
Output side  
ground fault  
overcurrent  
protection  
This function stops the inverter output if a Check the motor cable Repair the wiring.  
ground fault overcurrent flows due to a  
ground fault which occurred in the  
insulation and  
connection for output  
inverter’s output (load) side. Use Pr. 249 short-circuit/ground  
“ground fault detection at start” to set  
whether the protective function is to be  
activated or not. (In the 400V class, the  
protective function is always active.)  
fault.  
External thermal If the external thermal relay designed for Check for motor  
relay operation motor overheat protection or the internally overheating.  
Load the machine  
properly to distribute  
the load evenly.  
mounted temperature relay in the motor  
Check to make sure  
switches on (contacts open), the inverter the machine is loaded  
output is stopped. If the relay contacts are properly and that the  
reset automatically, the inverter will not  
restart unless it is reset.  
load is balanced.  
Stall prevention The running frequency has fallen to 0 with Check the motor for a Verify that the AC  
stall prevention activated.  
“locked rotor”  
condition.  
drive’s parameters are  
correct.  
Contact Alliance  
Laundry Systems’  
Customer Service  
department.  
Output phase  
failure  
This function stops the inverter output if Check the wiring.  
one of the three phases (U, V, W) on the Check the motor for a connections.  
Tighten the wire  
protection  
inverter’s output side (load side) results in fault.  
open phase.  
Replace the  
connectors as needed.  
Fan fault  
For the inverter which contains a cooling Check the cooling  
Replace the fan as  
needed.  
fan, FN appears on the operation panel  
when the cooling fan fails.  
fan’s operation.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
57  
 
Inverter Drive Error Codes  
Operation  
Panel  
Name  
Description and NOTES  
Check point  
Corrective action  
Load the machine  
Indication  
Stall prevention During acceleration–If a current of more  
Check to make sure  
the machine is  
loaded properly and  
that the load is  
balanced.  
properly to  
distribute the load  
evenly.  
(overcurrent)  
than 150% of the rated inverter current  
flows in the motor this function stops the  
increase in frequency until the overload  
current reduces to prevent the inverter  
from resulting in overcurrent shut-off.  
ContactAlliance  
Verify that the AC  
Laundry Systems’  
Customer Service  
department.  
drive’s parameters  
are correct.  
When the overload current has reduces  
below 150%, this function increases the  
frequency again.  
During constant-speed operation–If a  
current of more than 150%, this function  
lowers the frequency again.  
When the overload current has reduces  
below 150%, this function increases the  
frequency again.  
During deceleration–If a current of more  
than 150% of the rated inverter current  
flows in the motor, this function stops the  
decrease in frequency until the overload  
current reduces to prevent the inverter  
from resulting in overcurrent shut-off.  
When the overload current has reduced  
below 150%, this function decreases the  
frequency again.  
Stall prevention During deceleration-If the regenerative  
Check to make sure  
Load the machine  
(overvoltage)  
energy of the motor exceeds the brake  
the machine is loaded properly to distribute  
capability, this function stops the decrease properly and that the the load evenly.  
in frequency to prevent overvoltage  
shutoff. As soon as the regenerative  
energy has reduced, deceleration resumes.  
STOP  
load is balanced.  
PU stop  
A stop made by pressing the  
key of Check for a stop made Perform operation  
RESET  
STOP  
RESET  
the PU has been set in Pr. 75 “PU stop  
selection”.  
by pressing the  
correctly.  
key of the operation  
panel during external  
operation.  
This alarm appears if:  
Perform operation  
correctly.  
The RES signal is on;  
You attempted to set any parameter  
value in the external operation mode;  
You attempted to change the operation  
mode during operation;  
You attempted to set any parameter  
value outside its setting range.  
You attempted to set any parameter  
value during operation (while signal  
STF or STR is ON).  
You attempted to set any parameter  
value while parameter write is being  
inhibited in Pr. 77 “parameter write  
inhibit selection”.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
58  
 
Inverter Drive Error Codes  
Operation  
Panel  
Indication  
Name  
Description and NOTES  
Check point  
Corrective action  
Under Voltage  
The power supply has fallen below a  
specified level.  
This fault appears  
every time the  
machine is powered  
down.  
Apply the proper  
voltage to the  
machine.  
Check the power  
supply voltage.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
9001889  
59  
 
 

Acme Kitchenettes Ventilation Hood PP 32 User Manual
Acu Rite Weather Radio 09150TRX User Manual
AEG Oven E3100 1 User Manual
Allied Telesis Network Card AT 2916SX User Manual
Altec Lansing Headphones UHP101 User Manual
Amcor Air Conditioner CPLM 12KE B 410 User Manual
AOSafety Home Safety Product Dust User Manual
Audiovox Remote Starter PRO9276TW User Manual
Behringer Computer Monitor B1030A User Manual
Beko Flat Panel Television 40WLU550FHID User Manual