Allied Telesis Power Supply AT MCF2000AC User Manual

Review the following before you begin to install the module in the chassis:  
Caution  
Refer to the chassis’ Installation Guide to verify that the module is  
Do not force the module into place. Doing so may damage the  
connector pins on the backplane inside the chassis.  
appropriate for the unit.  
For instructions on how to remove a power supply module, refer to the  
chassis’s Installation Guide.  
The AT-MCF2000AC power supply module is hot-swappable. You can  
install or replace the module while the chassis is powered on.  
Refer to the chassis’ Installation Guide for a list of safety precautions to  
observe when installing the power supply module in the unit.  
A
The following procedure uses the AT-MCF2000 media converter chassis  
AT-MCF2000AC Power Supply Module  
Installation Guide  
M
A
ANA  
T
-
MCF2KPN  
L3  
G
for illustration purposes. Your chassis may be different.  
ST  
N
F
A
A
O
U
T
R
L
US  
P
S
U
M
A
T
L
F
A
N
Package Contents  
1111-a  
Make sure the following items are included in the shipping package. If an item  
is missing or damaged, contact your Allied Telesis sales representative for  
assistance.  
Allied Telesis, Inc.  
One AT-MCF2000AC power supply module  
Four regional AC power cords  
One power cord retaining clip  
This Installation Guide  
Figure 3. Installing the AT-MCF2000AC Power Supply Module  
4. Secure the power supply module to the chassis by tightening the two  
captive screws using a cross-head screwdriver. Refer to Figure 4.  
Overview  
Installing the AT-MCF2000AC Power Supply Module  
The AT-MCF2000AC module is an AC power supply unit for the AT-MCF2000  
series of media converter chassis.  
To install the AT-MCF2000AC power supply module, perform the following  
procedure:  
ST  
N
F
A
A
O
U
T
R
L
US  
P
S
U
M
A
L
T
1. Remove the power supply module from the shipping package. Store the  
packaging material in a safe location. You must use the original shipping  
material if you need to return the unit to Allied Telesis.  
F
A
N
A
AT  
-
MCF2KPNL3  
M
2. Remove a blank panel from a power supply/fan module slot on the back  
panel of the chassis by loosening the two captive screws of the panel with  
a cross-head screwdriver. Refer to the chassis’ Installation Guide for the  
location of the power supply/fan module slots.  
1113-a  
Figure 4. Securing the Power Supply Module  
ST  
A
T
NORUMASL  
FA  
PSU  
U
L
T
FA  
N
5. Locate the retaining brackets on either side of the AC power connector.  
1110-a  
A
AT  
-
MCF2KPN  
L2  
AT  
-
MCF2KPN  
Figure 1. AT-MCF2000AC Power Supply Module  
M
A
L3  
S
TA  
NORMAL  
TUS  
PSU  
Note  
FA  
U
LT  
1111-a  
FA  
N
For a list of available chassis models in the AT-MCF2000 media  
converter product line, contact your Allied Telesis sales representative or  
visit our web site.  
A
AT  
-
MCF2KPNL3  
M
Figure 2. Removing the Blank Panel from a Power Supply/Fan Module Slot  
3. Slide the power supply module into the slot as shown in Figure 3, until it is  
flush with the back panel of the chassis. Light pressure may be needed to  
seat the module on the connector on the back panel of the chassis.  
Retaining Clip Brackets  
Figure 5. Locating the Retaining Clip Brackets  
3
*613-000575 RevA*  
613-000575 Rev A  
1
2
 
     

Acer Computer Monitor X233HZ User Manual
ADTRAN Network Card TSU 120 User Manual
AEG Refrigerator SKS71200F0 User Manual
Air King Ventilation Hood AK110LS User Manual
Aiwa Car Stereo System CDC X136 User Manual
Alpine Car Stereo System CDE103BT User Manual
American Standard Bathroom Aids 2351 User Manual
Apple Musical Toy Instrument 72 User Manual
Atlantic Carrying Case Gaming Travel Bag User Manual
Audiovox Speaker AVW110 User Manual