Beko Hair Dryer DCU 6130B User Manual

Condenser  
Sensor Dryer  
DCU 6130W  
DCU 6130S  
DCU 6130B  
 
TABLE OF CONTENTS  
1 Your Dryer  
Overview .............................................4  
Technical Specifications.......................5  
Auxiliary function................................17  
Warning indicators.............................17  
Time delay.........................................17  
Starting the programme.....................17  
Progress of programme.....................17  
Changing the programme after it has  
started...............................................17  
Child-proof lock.................................18  
Finishing by cancelling the programme18  
End of programme ............................19  
4
2 Important safety information6  
General safety .....................................6  
Intended use .......................................7  
Childrens safety ..................................7  
3 Installation  
8
7 Maintenance and cleaning 20  
Appropriate installation location ...........8  
Removing the transportation safety  
Filter Cartridge / Door Inner Surface...20  
Sensor ..............................................20  
Water tank;........................................20  
For the condenser ............................21  
assembly.............................................8  
Under counter installation ....................8  
Mounting over a washing machine.......8  
Connection to water drain; ..................8  
Adjusting the feet.................................9  
First use ..............................................9  
Disposing of packaging material ..........9  
Transportation of the machine .............9  
Disposing of the old machine...............9  
8 Suggested solutions for  
problems  
23  
24  
9 Guarantee  
What is covered?...............................24  
What is not covered?.........................24  
Important notes.................................24  
4 Electrical Connection  
10  
Attention!...........................................10  
Electrical requirements.......................10  
Fitting a different plug .......................10  
Washer/dryer combination.................10  
10 Service  
25  
5 Initial preparations for drying11  
Things to be done for energy saving:.11  
Laundry suitable for drying in the  
machine ............................................11  
Laundry unsuitable for drying in the  
machine ............................................11  
Preparing laundry for drying...............12  
Correct load capacity ........................12  
6 Selecting a Programme and  
OperatingYour Machine  
13  
Control panel.....................................13  
Preparing the machine.......................14  
Programme selection.........................16  
Programme selection and consumption  
table..................................................16  
 
1 Your Dryer  
Overview  
7
1
6
5
2
4
3
1- Control panel  
5- Rating plate  
6- Fluff filter  
2- Kick plate opening tab  
3-Adjustable feet  
7- Power cord  
4-Kick plate  
Download from Www.Somanuals.c4om.EANll Manuals Search And Download.  
Technical Specifications  
EN  
2
Height (adjustable)  
Width  
84.6 cm  
59.5 cm  
53 cm  
6 kg  
Depth  
Capacity (max.)  
Weight (net)  
36 kg  
Voltage  
Rated power input  
Model code  
See type label  
Type label is located behind the loading door.  
Specifications of this appliance may change without notice to improve the quality of the product.  
Figures in this manual are schematic and may not match your product exactly.  
Values stated on the machine labels or in the documentation accompanying it are obtained in  
laboratory in accordance with the relevant standards. Depending on operational and environmental  
conditions of the appliance, values may vary.  
 
5 EN  
2 Important safety instructions  
This section includes safety information that will  
help protection from risks of personal injuries  
or damages. Failure to follow these instructions  
Do not make any changes on the plug  
supplied with the product. If it is not  
compatible with the socket, have a  
qualified electrician change the socket with  
a suitable one.  
sGheallnceaursaelasnayfweatryranty to become void.  
Items cleaned or washed with gasoil/  
fuel oil, dry-laundry solvents and other  
combustible or explosive materials as  
well as the items that are contaminated  
or spotted with such materials should not  
be dried in the product since they emit  
flammable or explosive vapor.  
Never place the machine on a carpet-  
covered floor, otherwise, lack of airflow  
beneath the machine may cause electrical  
parts to overheat. This will cause problems  
with your machine.  
If the power cable or mains plug is  
damaged, you must call Authorised Service  
Agent for repair.  
The product should not be plugged in  
during installation, maintenance and repair  
works. Such works should always be made  
by the technical service. Manufacturer shall  
not be held responsible for damages arising  
from processes carried out by unauthorised  
persons.  
Do not dry items cleaned with industrial  
chemicals in the dryer.  
Do not dry unwashed items in the dryer.  
Items soiled with cooking oils, acetone,  
alcohol, fuel oil, kerosene, stain remover,  
turpentine, paraffin and paraffin removers  
must be washed in hot water with plenty of  
detergent before being dried in the dryer.  
Garments or pillows bolstered with rubber  
foam (latex foam), shower bonnets, water  
resistant textiles, materials with rubber  
reinforcement and rubber foam pads  
should not be dried in the dryer.  
Connect the product to a grounded outlet  
protected by a fuse of suitable capacity as  
stated in the technical specifications table.  
Operate your product at temperatures  
between +5°C and +35°C.  
Do not use fabric softeners and anti-static  
products unless they are recommended by  
the manufacturers of the fabric softener or  
the product.  
This product must be earthed. Grounding  
installation decreases the risk of electric  
shock by opening a path with low  
resistance for the electricity flow in case of  
a malfunction or failure. Power cable of this  
product is equipped with a conductor and  
a grounding plug that allows for grounding  
the product. This plug must be installed  
appropriately and inserted into a socket  
which is grounded in accordance with the  
local laws and regulations.  
Do not use electrical devices in the product.  
Do not connect the air exit of the product  
to the exit ducts which are used for the  
exhaust fumes of the devices operating  
with gas or other types of fuel.  
You must provide enough ventilation in  
order to prevent gases exiting from devices  
operating with other types of fuels including  
the naked flame from accumulating in the  
room due to the back fire effect.  
Always clean the lint filter before or after  
each loading.  
Never operate your dryer without the lint  
filter installed.  
Do not allow fibre, dust and dirt  
Do not install the product behind a door  
with a lock, sliding door or a door that has  
a hinge against the hinge of the dryer.  
Do not install or leave this product in  
places where it will be exposed to outdoor  
conditions.  
accumulation around the exhaust exit and  
at adjacent areas.  
Power cable plug must be within easy  
reach after installation.  
Do not use extension cords, multi-plugs  
or adaptors to connect the dryer to power  
supply in order to decrease the risk of  
electric shock.  
Do not tamper with the controls.  
Do not perform any repair or part replacing  
Download from Www.Somanuals.c6om.EANll Manuals Search And Download.  
procedures on the product even if you  
know or have the ability to perform unless  
it is clearly suggested in the operating  
instructions or the published service  
manual.  
Inside and exhaust duct of the product  
must be cleaned by the qualified service  
personnel periodically.  
Wrong connection of grounding conductor  
of the product can cause electric shock. If  
you have any suspect about the grounding  
connection, have it checked by a qualified  
electrician, service representative or service  
personnel.  
a dryer. Damage to the dryer can result if  
metal reinforcements come loose during  
drying.  
Check all garments for forgotten lighters,  
coins, metal pieces, needles, etc. before  
loading.  
At times when your dryer is not in use or  
after the laundry is taken out following the  
completion of drying process, turn off by  
using the On/Off button. In cases when  
the On/Off button is on (while the dryer  
is energized), keep the door of the dryer  
closed.  
Intended use  
Do not reach into the machine when the  
drum is spinning.  
This product has been designed for  
domestic use. It should not be used for  
other purposes.  
Unplug the machine when it is not in use.  
Never wash down the appliance with water!  
There is the risk of electric shock! Always  
disconnect by unplugging from the mains  
before cleaning.  
Never touch the plug with wet hands.  
Never unplug by pulling on the cable,  
always pull out by grabbing the plug only.  
Do not operate the machine if the power  
cable or plug is damaged!  
Use the product only for drying laundry that  
are marked accordingly.  
Dry only those articles in your product that  
are stated in this manual.  
This product is not intended to be used by  
persons with physical, sensory or mental  
disorders or unlearned or inexperienced  
people (including children) unless they  
are attended by a person who will be  
responsible for their safety or who will  
instruct them accordingly for use of the  
product.  
Never attempt to repair the machine  
yourself, otherwise, you will be putting your  
life and others’ lives in danger.  
For malfunctions that cannot be solved by  
following the information given in the safety  
instructions:  
Turn off the machine and contact an  
authorised service agent.  
Do not stop the dryer before the drying  
cycle comes to an end unless you will  
remove all laundry from the dryer quickly in  
order to hang them and dissipate the heat.  
Remove the door of the drying  
Children’s safety  
Electrical appliances are dangerous for  
the children. Keep children away from the  
machine when it is operating. Do not let  
them tamper with the machine.  
Packaging materials are dangerous to  
children. Keep the packaging materials out  
of reach of children or dispose them by  
classifying according to waste directives.  
Do not allow children sit/climb on or enter  
in the product.  
compartment before decommissioning or  
disposing of the product.  
Children should be supervised to ensure  
that they do not play with the product.  
Close the loading door when you leave the  
area where the product is located.  
The final step of the drying cycle (cool-  
down cycle) occurs without applying  
heat to ensure that the items are left at a  
temperature that will not damage them.  
Fabric softeners or similar products should  
be used as specified by the fabric softener  
instructions.  
Underwear that contains metal  
reinforcements should not be placed in  
 
7 EN  
3 Installation  
APrior to installation, visually check if the  
product has any defects on it. If so, do not have  
it installed. Damaged products will cause risks  
for your safety.  
Appropriate installation location  
Install the product in an environment which  
has no risk of freezing and is in a stable  
and level position.  
Operate your product in a well ventilated,  
dust-free environment.  
Do not block the air ducts in front of and  
under the product with materials such as  
long pile rugs and wooden plinths.  
Do not place your product on a long pile  
rug or on similar surfaces.  
Do not install the product behind a door  
with a lock, sliding door or a hinged door  
which can strike the product.  
AMake sure that you have removed  
the transportation safety assembly  
(nylon+styrofoam pieces) before using the  
product for the first time. Do not leave any  
items inside the drum.  
Once the product is installed, it should stay  
at the same place where its connections  
have been made. When installing the  
product, make sure that the rear wall of it  
does not touch anywhere (tap, socket, etc.)  
and also pay attention to install the product  
at a place where it will stay permanently.  
Under counter installation  
The product should never be operated  
without the top trim.  
Leave at least 3 cm of space between  
the side and rear walls of the product and  
the walls of the counter/cupboard when  
installing your product under a counter or  
in a cupboard.  
BDo not place the product on top of the  
power cable.  
Keep at least 1.5 cm distance to walls of  
Mounting over a washing  
machine  
Reomthoervfiunrngitutrhe.e transportation  
A fitting device should be used between  
the two machines when installing above  
a washing machine. The bracket must be  
installed by the Authorised Service Agent.  
Place the product on a firm floor. If it will be  
placed on top of a washing machine, the  
approximate weight of both machines may  
reach 180 kg when they are full. Therefore,  
the floor must be capable of carrying the  
load on it!  
safety assembly  
ARemove the transportation safety assembly  
before using the product for the first time.  
1. Open the loading door.  
2. There is a nylon bag inside the drum that  
contains a piece of styrofoam. Hold it from  
its section marked with XX.  
3. Pull the nylon towards yourself and remove  
the transportation safety assembly.  
Connection to water drain;  
In products equipped with a condenser unit the  
water accumulated during the drying cycle is  
collected in the water tank. You should drain the  
accumulated water after each drying cycle.  
You can directly send the accumulated water  
out through the water drain hose supplied with  
the machine instead of periodically draining the  
Download from Www.Somanuals.c8om.EANll Manuals Search And Download.  
water collected in the water tank.  
Connecting the water drain hose;  
C Never unscrew the adjustable feet from  
Firtshteiur hsoeusings.  
To have the product ready for operation  
before calling the authorised service agent,  
make sure that its location and power  
supply installations are appropriate. If they  
are not, call a qualified electrician to have  
any necessary arrangements carried out.  
Make sure that the power connections of  
the product are in accordance with the  
instructions given in relevant chapters of  
this manual.  
1. Remove the hose on the machine by  
pulling it out from its end. Do not use any  
tools to take out the hose.  
2. Connect the special drain hose supplied  
with the machine to the pipe fitting.  
3. The other end of the drain hose can be  
directly connected to the wastewater  
drain or to the washbasin. The fitting  
must always be secured in all types of  
connections. Your house may be flooded  
if the hose gets out of its housing during  
water discharge.  
Disposing of packaging material  
Packaging materials are dangerous to children.  
Keep packaging materials in a safe place out  
of reach of children. Packaging materials of  
your product are manufactured from recyclable  
materials. Sort and dispose of them in  
accordance with recycled waste instructions.  
Do not dispose of them with normal domestic  
wTraastne.sportation of the machine  
1. Unplug the machine from the mains.  
2. Remove the water drain and vent  
connections (if any).  
3. Drain water remaining in the machine  
completely before transportation.  
Disposing of the old machine  
Dispose of your old machine in an  
environmentally friendly manner.  
Refer to your local dealer or solid waste  
collection centre in your area to learn how to  
dispose of your machine.  
Before disposing of your old machine, cut off  
the power cable plug and make the loading  
door lock unusable to avoid dangerous  
conditions to children.  
Important:  
The hose should be attached to a height of  
maximum 80 cm.  
You must be careful not the pinch or bend  
the hose.  
The end of the hose should not be bent,  
it should not be stepped on and it must  
not be folded between the drain and the  
Admjuaschtiinneg. the feet  
In order to ensure that your machine operates  
more silently and vibration-free, it must stand  
level and balanced on its feet. Balance the  
machine by adjusting the feet.  
Rotate the feet to adjust until the machine  
stands level and firmly.  
 
9 EN  
4 Electrical Connection  
A Undercounter installation without the  
top cover must only be carried out by an  
authorised agent.Risk of electric shock.  
A Important  
Make sure that you have an earthed power  
outlet socket rated at 13 amps (minimum).  
Attention!  
If you use your dryer as built-in, the socket  
must be reachable after installation, or a  
separate switch (which can disconnect the  
two poles) must be used in the installation.  
Check for suitability.  
For a permanent connection, a master switch  
with at least 3mm contact clearance and  
minumum 13 A rating must be used.  
Fitting a different plug  
As the colours of the wires in the mains lead  
of this appliance may not correspond with the  
coloured markings identifying the terminals on  
your plug, proceed as follows:  
1 Connect the green - yellow or green (earth)  
wire to the terminal in the plug marked ‘E’ or  
with the symbol or coloured green and yellow  
or green.  
2 Connect the blue (neutral) wire to the terminal  
in the plug marked ‘N’ or coloured black.  
3 Connect the brown (live) wire to the terminal  
in the plug marked ‘Lor coloured red.  
With the alternative plugs a 13A fuse must  
be fitted either in the plug or adaptor or in the  
main fuse box. If in doubt contact a qualified  
Electrical requirements  
Before you insert the plug into the wall socket  
make sure that the voltage and the frequency  
shown in the rating label corresponds to your  
electricity supply.  
We recommend that this appliance be  
connected to the mains supply via a suitable  
switched and fused socket in a readily  
accessible position.  
electrician.  
Green and yellow  
or green  
Should the mains lead of the appliance  
become damaged or need replacing at any  
time, it must be replaced by a special purpose  
made mains lead which can only be obtained  
from a Authorised Service Agent.  
A Warning  
This appliance must be earthed  
If the fitted moulded plug is not suitable for your  
socket, then the plug should be cut off and an  
appropriate plug fitted.  
N
L
The moulded plug on this appliance  
incorporates a 13A fuse. Should the fuse need  
to be replaced an ASTA approved BS1362 fuse  
of the same rating must be used. Do not forget  
to refit the fuse cover. In the event of losing the  
fuse cover, the plug must not be used until a  
replacement fuse cover has been fitted. Colour  
of the replacement fuse cover must be the  
same colour as that visible on the pin face of  
the plug. Fuse covers are available from any  
good electrical store.  
Blue or black  
Brown or red  
Washer/dryer combination  
Do not stack washing machine on top of  
the tumble dryer. This would damage both  
appliances and guarantees would become  
void. It is also unsafe to stack an appliance  
on top of another without using a suitable  
and approved stacking kit obtained from the  
specialist retailers.  
In order to avoid hazards, damaged supply  
cord should be replaced by the manufacturer,  
its service agent or similarly qualified people.  
Built-under installation  
This appliance can be installed under a  
worktop.  
 
10 EN  
5 Initial preparations for drying  
Things to be done for energy  
saving:  
A B C D  
Make sure that you operate the product  
at its full capacity but pay attention to not  
exceeding it.  
Low  
Spin your laundry at the highest speed  
possible when washing them. Thus,  
the drying time is shortened and energy  
consumption is decreased.  
l n m  
o p q  
Pay attention to dry same types of laundry  
together.  
Follow the instructions in the user manual  
for programme selection.  
Make sure that sufficient clearance is  
provided at the front and rear side of the  
dryer for air circulation. Do not block the  
grill at the front side of the product.  
Do not open the door of the machine  
during drying unless necessary. If you must  
certainly open the door, pay attention not to  
keep it open for a long time.  
Laundry unsuitable for drying in  
the machine  
Laundry items with metal attachments such  
as belt buckles and metal buttons can  
damage your dryer.  
Do not dry items such as woollens, silk  
garments and nylon stockings, delicate  
embroidered fabrics, laundry with metal  
accessories and items such as sleeping  
bags in the dryer.  
Laundry made of delicate and valuable  
fabrics as well as lace curtains can be  
creased. Do not dry them in the dryer!  
Do not dry items made of hermetic fibres  
such as pillows and quilts in the dryer.  
Laundry made of foam or rubber will be  
deformed.  
Do not add new (wet) laundry during  
drying.  
Lint and fibres released from the laundry to  
the air during the drying cycle are collected  
in the “Lint Filter”. Make sure that you clean  
the filters before or after each drying.  
In models with condenser, make sure that  
you clean the condenser regularly at least  
once every month or after every 30 drying  
cycles.  
In vented models, follow the hose  
connection rules in the user manual and  
pay attention to the hose cleaning.  
Ventilate the room, where the dryer is  
located, well during drying.  
Do not dry laundry containing rubber in the  
dryer.  
Do not dry laundry exposed to petroleum,  
oil, combustible or explosive agents in the  
dryer even if they are washed beforehand.  
Overly wet laundry or laundry with dripping  
water must not be put into the dryer.  
Items cleaned or washed with gasoil/  
fuel oil, dry-laundry solvents and other  
combustible or explosive materials as  
well as the items that are contaminated  
or spotted with such materials should not  
be dried in the product since they emit  
flammable or explosive vapor.  
For power saving in models with lamps, at  
times when your dryer is not in use, keep  
the door closed if the On/Off button is  
Lapurnesdserdy(sif uthietadrbyeler isfoenredrgrizyeidn).g in  
the machine  
CAlways follow the suggestions on the  
laundry labels. Dry only the laundry having  
a label stating that they are suitable for  
drying in a dryer and make sure that you  
select the appropriate programme.  
 
11 EN  
Do not dry items cleaned with industrial  
chemicals in the dryer.  
Do not dry your unwashed laundry in the  
dryer.  
AConsider the information in the  
“Programme Selection Table”. Always start  
the programme in accordance with the  
maximum load capacity.  
CAdding laundry to the machine more  
than the level shown in the figure is not  
recommended. Drying performance will  
degrade when the machine is overloaded.  
Furthermore, your dryer and your laundry  
can be damaged.  
Items soiled with cooking oils, acetone,  
alcohol, fuel oil, kerosene, stain remover,  
turpentine, paraffin and paraffin removers  
must be washed in hot water with plenty of  
detergent before being dried in the dryer.  
Garments or pillows bolstered with rubber  
foam (latex foam), shower bonnets, water  
resistant textiles, materials with rubber  
reinforcement and rubber foam pads  
should not be dried in the dryer.  
Do not use fabric softeners and anti-static  
products unless they are recommended by  
the manufacturers of the fabric softener or  
the product.  
Do not dry the underwear reinforced with  
metal parts in the dryer. If these metal  
reinforcements loosen and break during  
drying, they will damage your dryer.  
CPlace your laundry into the drum loosely so  
that they will not get tangled.  
Following weights are given as examples.  
Approximate  
weights (g)  
Home articles  
Cotton quit covers (double)  
Cotton quit covers (single)  
Bed sheets (double)  
Bed sheets (single)  
1500  
1000  
500  
350  
700  
250  
100  
700  
350  
Large tablecloths  
Small tablecloths  
Preparing laundry for drying  
Check all laundry items before loading them Tea napkins  
into the product to make sure that there are  
no lighters, coins, metal items, needles and  
etc. in their pockets or on any part of them.  
Fabric softeners and similar products must  
be used in accordance with the instructions  
of the manufacturer of the relevant  
products.  
Bath towels  
Hand towels  
Approximate  
weights (g)  
Garments  
Blouses  
150  
300  
200  
500  
350  
700  
100  
125  
Cotton shirts  
Shirts  
All laundry must be spun at the highest spin  
speed that your washing machine allows  
for the laundry type.  
Laundry may be tangled after washing.  
Separate your laundry before placing them  
into your dryer.  
Sort your laundry according to their types  
and thicknesses. Dry the same type of  
laundry together. E.g.: fine kitchen towels  
and table cloths dry faster than the thick  
bath towels.  
Cotton dresses  
Dresses  
Jeans  
Handkerchiefs (10 pieces)  
T-Shirts  
Loading  
Open the loading door.  
Correct load capacity  
Place laundry items loosely into the dryer.  
Push the loading door to close. Ensure that  
no items are caught in the door.  
 
12 EN  
6 Selecting a Programme and OperatingYour Machine  
Control panel  
4
1
2
3
7
6
5
1. Filter cleaning warning light  
Warning light turns on when the filter is full.  
2. Programme follow-up indicator  
5. Programme selection knob  
Used to select a programme.  
6. Start/Pause/Cancel button  
Used to follow-up the progress of the  
Used to start, pause or cancel the  
current programme.  
3. Cancel audio warning  
programme.  
7. Water tank warning light*  
Used to cancel the audio warning given at  
Warning light turns on when the water tank  
is full.  
the end of the programme.  
4. On/Off button  
Used to turn on and off the machine.  
 
13 EN  
compared to the cottons programme. It is  
recommended for your synthetic laundry (such  
as shirts, blouses, synthetic/cotton blended  
Preparing the machine  
1. Plug in your machine.  
2. Place the laundry in the machine.  
3. Press the “On/Off” button.  
CPressing the “On/Off” button does not  
necessarily mean that the programme has  
started. Press "Start/Pause/Cancel" button  
laundry, etc.).  
C Do not dry curtains and lace in your  
machine.  
Anti-creasing  
A 2-hour anti creasing programme to prevent  
laundry from creasing will be activated if you do  
not take the laundry out after the programme  
is over. This programme rotates the laundry in  
10-minute intervals to prevent creasing.  
Special programmes  
For special cases, there are also extra  
programmes available:  
CAdditional programmes may differ  
according to the model of your machine.  
•Xpress 35’ min.  
You can use this programme to dry the cottons  
that are spun at high speeds in your washing  
machine. It can dry your 2 kg Cotton laundry (3  
Shirts / 5 T-Shirts) within 35 minutes.  
CIn order to obtain better results from the  
dryer programmes, your laundry must be  
washed with suitable programme and spun  
at the recommended spin speeds in your  
washing machine.  
of the machine to start the programme.  
Programme selection  
Decide the appropriate programme from  
the table below which includes drying  
temperatures in degrees. Select the desired  
programme with the programme selection  
button.  
Dry at high temperature only  
for cotton laundry. Thick and  
multi layered laundry (E.g.:  
towels, linens, jeans) are dried  
Extra dry  
in a way that they do not  
require ironing before placing in  
the wardrobe.  
Normal laundry (E.g.:  
tablecloths, underwear) are  
Cupboard  
dried in a way that they do not  
dry  
require ironing before placing in  
the drawers.  
• Shirts  
Normal laundry (E.g.:  
tablecloths, underwear) are  
dried in a way that they do not  
require ironing before placing  
in the drawers, but more  
than those in the ready to  
wearoption.  
Normal laundry (E.g., Shirts,  
dresses) are dried ready to be  
ironed.  
Dries the shirts in a more sensitive way so that  
they are less creased and ironed easily.  
CShirts may contain little amount of  
dampness at the and of the programme.  
It is advised not to leave the shirts in the  
dryer.  
Normal dry  
Iron Dry  
•Jeans  
You can use this programme to dry the jeans  
that are spun at high speeds in your washing  
machine.  
.
CReview the relevant part of the programme  
C For further programme details, see,  
table.  
“Programme Selection Table”  
Main programmes  
Depending on the type of laundry, the following  
main programmes are available:  
Cottons  
You can dry your durable laundry with this  
programme. Dries at high temperature. It is  
recommended to use for your cotton items  
(such as bed sheets, quilt cover, underclothing,  
etc.).  
Synthetics  
•Delicates  
You can dry at a lower temperature your very  
delicate laundry (silk blouses, fine underwear,  
etc.) that are suitable for drying or laundry which  
is advised to be hand-washed.  
CIt is recommended to use a cloth bag to  
avoid certain delicate garments and laundry  
from getting creased or damaged. Take  
your garments immediately out of the dryer  
and hang them after the programme ends  
in order to prevent them being creased.  
You can dry your less durable laundry with this  
programme. It dries at a lower temperature  
 
14 EN  
• Freshen Up  
Only ventilation is performed for 10 minutes  
without blowing hot air. You can air your clothes  
that have been kept at closed environments  
for a long time thanks to this programme to  
deodorize unpleasant odours.  
•Timer programmes  
You can select one of the 10 min., 20 min.,  
40 min. and 60 min. timer programmes to  
achieve the desired final drying level at low  
temperatures. Programme dries at the selected  
time regardless of the drying temperature.  
 
15 EN  
Programme selection and consumption table  
EN  
Product Fiche  
Electric drier label Directive 95/13/EC  
Type of appliance  
Condensing  
B
Energy efficiency class  
Scale from A (Highest Efficiency) to G (Lowest Efficiency)  
Approximate  
Spin speed in  
Capacity (kg) washing machine  
(rpm)  
amount of  
remaining  
humidity  
Drying time  
(minutes)  
Programmes  
Cottons / Coloureds  
Cupboard dry  
6
6
6
1200-1000  
1200-1000  
1200-1000  
% 60  
% 60  
% 60  
99  
104  
77  
A
A
Normal dry  
Iron dry  
A
Xpress 35 min.  
Shirt  
2
1.5  
4
1400-1000  
1000-800  
1200-1000  
% 50  
% 50  
% 50  
35  
35  
75  
Jeans  
Synthetics  
Cupboard dry  
Cupboard dry  
3
800  
800  
% 40  
% 40  
38  
30  
B
Delicates  
1,5  
B
Energy consumption values  
Approximate  
amount of  
remaining  
humidity  
Spin speed in  
washing machine  
(rpm)  
Energy  
consumption value  
kWh  
Programmes  
Capacity (kg)  
Cottons linen cupboard dry*  
6
1000  
% 60  
3.36  
Cottons iron dry  
6
3
1000  
800  
% 60  
% 40  
2.77  
1.23  
Synthetics cupboard dry  
Annual Energy Consumption (kWh)**  
274.80  
* : Energy Label standard programme (EN 61121:2005)  
All values given in the table have been fixed according to EN 61121:2005 Standard. These values  
may deviate from the table according to the laundry type, laundry spin speed, environmental  
conditions and voltage fluctuations.  
**:Estimated annual consumption for a four-person house hold which normally dries using a drier.  
 
16 EN  
“Cupboard dry”:  
Auxiliary function  
Cancel audio warning  
Starts to illuminate when the drying degree  
reaches “Ready to wear” step and remains  
illuminated until the next step.  
Your dryer will give an audio warning when the  
programme comes to an end. If you do not  
want to hear the audio warning, press “Cancel  
Audio Warning” button. The relevant light  
will turn on when this button is pressed and  
an audio warning will not be given when the  
programme comes to an end.  
“Final / Anti-creasing”:  
- Illuminates when the programme comes to an  
end and anti-creasing function is activated.  
CIf more than one LED light up or  
flash concurrently, it means there is  
malfunctioning or a failure (please see,  
Solution suggestions for problems).  
Changing the programme after it  
CYou can select this function either before or  
after the programme starts.  
Warning indicators  
CWarning indicators may differ according to  
the model of your dryer.  
Filter cleaning  
has started  
You can use this feature to dry your clothes  
under higher or lower temperatures after your  
dryer has started.  
A warning light will turn on to remind filter  
cleaning after the programme finishes.  
CIf the filter cleaning warning light lights up  
continuously, please refer to, “Suggested  
solutions for problems”.  
Water tank  
Warning light starts flashing when the tank is  
filled with water. The dryer stops operating if  
the warning light turns on when a programme  
is running. Drain the water in the water tank to  
restart the dryer. Press “Start/Pause/Cancel”  
button to start the programme after you have  
emptied the water tank. The warning light turns  
off and the programme resumes operating.  
For example;  
1. Press and hold the “Start/Pause/Cancel”  
button for about 3 seconds to “Cancel”  
the programme in order to select “Extra  
Dry” programme instead of “Iron Dry”  
programme.  
2. Select the “Extra Dry” programme by  
rotating the programme selection button.  
3. Press “Start/Pause/Cancel” button to start  
the programme.  
CPress “Start/Pause/Cancel” button for  
3 seconds to cancel the programme or  
turn the programme selection knob in any  
direction to end the programme while the  
machine is running. Water tank and filter  
cleaning warning lights turn on to warn the  
user when the programme is cancelled by  
pressing the “Start/Pause/Cancel” button  
for 3 seconds. However, the warning  
lights do not turn on when the programme  
is cancelled by turning the programme  
selection knob. Only the drying light turns  
on and the machine remains in hold until  
a new programme is selected and the  
“Start/Pause/Cancel” button is pressed.  
Child-proof lock of the machine should  
not be active in order to perform these  
two operations. If the child-proof lock is  
active, deactivate it before performing these  
operations.  
Starting the programme  
1. Press “Start/Pause/Cancel” button to start  
the programme.  
2. Light of the “Start/Pause/Cancel” button  
will turn on to indicate that the programme  
has started.  
Progress of programme  
Progress of a running programme is shown  
through the programme follow-up indicator.  
At the beginning of every programme step, the  
relevant indicator LED will light up and light of  
the completed step will turn off.  
“Drying”:  
- Drying level will be illuminated during the whole  
drying process until the drying degree reaches  
“iron dry”.  
“Iron Dry”:  
- Starts to illuminate when the drying degree  
reaches “iron dry” step and remains illuminated  
until the next step.  
 
17 EN  
Adding/removing laundry in standby  
mode  
In order to add or remove laundry after the  
programme starts:  
1. Press the “Start/Pause/Cancel” button to  
switch the dryer to “Pause” mode. Drying  
process will stop.  
2. Open the door at “Pause” position and  
close it again after adding or taking out  
laundry.  
3. Press “Start/Pause/Cancel” button to start  
the programme.  
CPress the relevant buttons for 3 seconds  
to activate the child-proof lock. A long  
beep will be heard and the child-proof lock  
will be activated. A double beep will be  
heard if you press any button or turn the  
programme selection knob while the child-  
proof lock is active. Press the buttons for 3  
seconds to deactivate the child-proof lock.  
Single beep will be heard and child-proof  
lock will be deactivated.  
AA double beep will be heard if you turn  
the programme selection knob when the  
machine is running and the child-proof lock  
is active. If you deactivate the child-proof  
lock without returning the programme  
selection knob to its previous position, the  
programme will be terminated since the  
position of the programme selection knob  
is changed. The drying light turns on and  
the machine remains on hold until a new  
programme is selected and the “Start/  
Pause/Cancel” button is pressed.  
CAny laundry added after the drying process  
has started may cause the dried clothes in  
the machine intermingle with wet clothes  
and the result will be wet laundry after the  
drying process is over.  
CLaundry may be added or taken out  
as much as desired during a drying  
process, but this process will extend the  
programme duration and increase energy  
consumption since the drying will be  
interrupted continuously. Therefore, it is  
recommended to add laundry before the  
drying programme has started.  
Child-proof lock  
There is a child-proof lock to prevent any  
programme interruption due to the pressing of  
button while the programme is running. The  
loading door and all buttons except the “On/  
Off” button on the control panel are deactivated  
when the child-proof lock is active.  
Press the “Start/Pause/Cancel” and “Cancel  
audio warning” buttons simultaneously for 3  
seconds to activate the child-press lock.  
To start a new programme after the programme  
is over or to interrupt the programme, the child-  
proof lock should be deactivated. Press the  
same buttons for 3 sec. again to deactivate the  
child-proof lock.  
Finishing by cancelling the  
programme  
To cancel any selected programme:  
Press “Start/Pause/Cancel” button for about 3  
seconds. The “Filter cleaning”, “Water tank” and  
“End/ Anti-creasing” warning lights will turn on  
at the end of this period for reminding purposes.  
AAs the inside of the dryer will be excessively  
hot when you cancel the programme while  
the dryer is running, activate the ventilation  
programme to cool it down.  
CChild-proof lock is deactivated when the  
machine is restarted by pressing the On/Off  
button.  
 
18 EN  
End of programme  
The “End/Anti-creasing”, “Filter cleaning” and  
“Water tank” warning lights on the programme  
follow up indicator will turn on when the  
programme comes to an end. The door can be  
opened and the machine becomes ready for a  
second cycle.  
Press “On/Off” button to turn off the dryer.  
CFinal step of the drying cycle (cooling step)  
is performed without heat application in  
order to keep the items at a temperature  
that would not harm them.  
CA 2-hour anti creasing programme to  
prevent laundry from creasing will be  
activated if you do not take the laundry out  
after the programme has come to an end.  
CIf you will not take the laundry out  
immediately, do not stop the dryer before  
the drying process is complete.  
CClean the filter after each drying (please  
see, Filter cleaning).  
CDrain the water tank after each drying  
(please see, Water tank)  
 
19 EN  
7 Maintenance and cleaning  
Filter Cartridge / Door Inner  
Surface  
Lint and fibres released from the laundry to the  
air during the drying cycle are collected in the  
“Filter Cartridge”.  
CSuch fibre and lint are generally formed  
during wearing and washing.  
CAlways clean the filter and the inner  
surfaces of the cover after each drying  
process.  
Sensor  
C You can clean the filter and filter area by  
vacuum cleaner.  
To clean the filter:  
1. Open the loading door.  
2. Remove the cover filter by pulling it up and  
open the filter.  
3. Clean lint, fibre, and cotton by unravelling  
by hand or with a soft piece of cloth.  
4. Close the filter and place it back into its  
seat.  
C Clogging may arise on the filter surface  
after using your machine for some time; if  
this occurs, wash the filter with water and  
dry it before using again.  
There are humidity sensors in your dryer that  
detect whether the laundry is dry or not.  
To clean the sensor:  
1. Open the loading door of the dryer.  
2. Allow the machine to cool down if drying  
has been carried out.  
3. Wipe the metal sensors with a soft cloth,  
dampened with vinegar and dry them.  
C Clean metal sensors 4 times a year.  
ANever use solvents, cleaning agents  
or similar substances when cleaning  
since these materials can cause fire and  
explosion!  
Water tank;  
The moisture in the damp laundry is taken from  
the laundry and condensed. Drain the water  
tank after each drying cycle or during drying  
when “Water tank” warning light turns on.  
C Clean the entire inner surface of the door  
and door gasket by wiping with a damp  
cloth.  
 
20 EN  
For the condenser  
ACondensed water is not drinkable!  
ANever take out the water tank when the  
programme is running!  
Hot and humid air in the condenser is cooled  
with the cold air from the room. Thus, the humid  
air circulating in your dryer is condensed and  
then pumped into the tank.  
If you forget to drain the water tank, your  
dryer will stop during the following drying  
cycles when the water tank is full and the  
“Water tank” warning light will turn on. If  
this is the case, press the “Start/Pause/  
Cancel” button to resume the drying cycle  
after draining the water tank.  
C Clean the condenser after every 30 drying  
cycles or once a month.  
To clean the condenser:  
1. If a drying process has been carried out,  
open the door of the machine and wait  
until it cools down.  
To drain the water tank:  
1. Drain the water as shown on the picturre .  
2. Unlock the 2 condenser locks after opening  
2. If there is lint accumulation in the water  
the kick plate.  
tank cover, clean it and press to close.  
3. Place the water tank into its seat.  
3. Pull out the condenser.  
 
21 EN  
4. Clean the condenser by applying  
pressurized water with a shower head and  
wait until the water drains.  
5. Place the condenser in its housing. Fasten  
the 2 locks and make sure that they are  
seated securely.  
6. Close the kick plate cover.  
 
22 EN  
8 Suggested solutions for problems  
Drying process takes too much time  
Meshes of the filter may be clogged. Wash with water  
Laundry comes out wet at the end of drying.  
Meshes of the filter may be clogged. Wash with water.  
Excessive laundry might have been loaded in. Do not load the dryer in excess.  
Dryer does not switch on or the programme does not start. Dryer is not activated when set.  
It might have not been plugged in. Make sure that the machine is plugged in.  
The loading door may be ajar. Make sure that the loading door is properly closed.  
Programme might have not been set or the «Start/Pause/Cancel» button might have not  
been pressed. Make sure that the programme has been set and it is not in “Pause” mode.  
«Childproof lock» might have been activated. Deactivate the childproof lock.  
Programme has been interrupted without any cause.  
The loading door may be ajar. Make sure that the loading door is properly closed.  
Electricity may be cut off. Press «Start/Pause/Cancel» button to start the programme.  
Make sure that the condenser cover and the red lock is closed securely.  
Laundry has shrunk, become felted or deteriorated.  
A programme suitable for the laundry type might have not been used. Dry only the laundry  
which is suitable for drying in dryer after checking the labels on your clothes.  
Select a programme with suitable low temperature for the laundry type to dry your clothes.  
Drum lightning does not come on. (For models with lamp)  
Dryer might have not been started by using the «On/Off» button. Make sure that the dryer is  
on.  
Bulb may have blown. Call the authorized service to replace the bulb.  
“Final / Anti-creasing” LED flashes.  
The 2-hour anti creasing programme to prevent laundry from creasing might have been  
activated. Turn off the dryer and take out the laundry.  
“Final / Anti-creasing” LED is on.  
Programme has come to an end. Turn off the dryer and take out the laundry.  
The “Drying” LED flashes.  
A heat sensor failure has occurred. Dryer ends the programme without heating. Turn off the  
dryer and take out the laundry. Call your authorized service  
• “Filter cleaning” LED is on.  
Filter might have not been cleaned. Clean the cover filter.  
“Water comes out the cover”  
Clean the entire inner surface of the cover and door gasket.  
“Cover opens spontaneously.”  
Push it until you hear that it is closed.  
For products with a condenser:  
“Water tank” warning LED is on.  
Water may be full. Drain the water in the tank.  
“Condenser cleaning” LED is on.  
Condenser might have not been cleaned. Clean the filters in the condenser under the kick  
plate.  
ACall an authorized service if the problem persists.  
 
23 EN  
9 Guarantee  
Your new product is guaranteed against the  
cost of breakdown repairs for twelve months  
from the date of the original purchase.  
What is covered?  
Important notes  
Your product is designed and built for  
domestic household use only.  
The guarantee will be void if the product  
is installed or used in commercial or non-  
residential domestic household premises.  
The product must be correctly installed,  
located and operated in accordance with  
the instructions contained in the User  
Instructions Booklet provided.  
Professional installation by a qualified  
Electrical Domestic Appliance Installer  
is recommended for all Washing  
Machines,Tumble Dryers, Dishwashers,  
Dryers and Electric Cookers  
Repairs necessary as a result of faulty  
materials, defective components or  
manufacturing defect.  
The cost of functional replacement parts,  
but excluding consumable  
items.  
The labour costs of a approved repairer to  
carry out the repair.  
What is not covered?  
Transit, delivery or accidental damage or  
misuse and abuse.  
Cabinet or appearance parts, including  
knobs, flaps, handles or container lids.  
Accessories or consumable items including  
but not limited to, ice trays, scrapers,  
cutlery baskets, filters and light bulbs.  
Repairs required as a result of  
Gas Cookers must only be installed by a  
Gas safe registered Gas Installer.  
The guarantee is given only within the  
boundaries of the United Kingdom and the  
Republic of Ireland.  
unauthorised repair or inexpert installation  
that fails to meet the requirements  
contained in the user instruction book.  
Repairs to products used on commercial  
or non-residential household premises.  
Loss of frozen food in freezers or fridge/  
freezers. (Food loss insurance is often  
included within your household contents  
insurance policy, or may be available  
separately from your retailer).  
The guarantee is applicable only to new  
products and is not transferable if the  
product is resold.  
Disclaims any liability for incidental or  
consequential damages.  
The guarantee does not in anyway diminish  
your statutory or legal rights.  
 
24 EN  
10 Service  
Please keep your purchase receipt or other  
proof of purchase in a safe place; you will  
need to have it should the product require  
attention under guarantee.  
You should also complete the details below;  
it will help us assist you when requesting  
service. (The model number is printed on the  
Instruction Booklet and the serial number  
is printed on the Rating Label affixed to the  
appliance)  
Service once the manufacturers  
guarantee has expired.  
If you have purchased an extended guarantee  
please refer to the instructions contained  
within the extended guarantee agreement  
document. Otherwise please call the  
appropriate number above where service can  
be obtained at a charge.  
Should you experience any difficulty in  
obtaining service please contact the Customer  
Help-Line.  
Tel: 0845 600 4911  
Model No:  
For service under guarantee simply telephone  
the appropriate number below.  
UK Mainland & Northern Ireland  
Fridges & Freezers 0845 600 4903  
Electric Cookers 0845 600 4902  
Gas & Dual Fuel Cookers  
0845 600 4905  
Washing Machines & Tumble Dryers  
0845 600 4906  
Serial No:  
Retailer:  
Date of purchase:  
Republic of Ireland  
All Refrigeration, 01 862 3411  
All Cookers  
Washing Machines & Dryers, Tumble Dryers  
Dishwashers  
Before requesting service please check the  
trouble-shooting guide in the Operating  
Instructions as a charge may be levied where  
no fault is found even though your product  
may still be under guarantee.  
 
25 EN  
 
 
 

3Com Switch S200 Series User Manual
Accton Technology Network Router VG3300 Series User Manual
Addonics Technologies Computer Drive RTM25N335H User Manual
ADT Security Services Home Security System NT9005 V10 NA User Manual
Advanced Wireless Solutions Portable Radio TK 3173 User Manual
Allied Telesis Switch AT FS708 xx User Manual
Amana Dishwasher W10261418A User Manual
American Standard Plumbing Product 2175503 User Manual
Bags and Gloves Network Card E 9220T User Manual
Barco Camcorder H400 User Manual